555814
8
Zoom out
Zoom in
Previous page
1/92
Next page
8
GB
SERVICE – NOTES ON MAINTENANCE 1
Oil replacement
Warm up engine on level ground
• Remove ller cap (12)
Open drain plug (7) and let oil drain completely into
a pan placed under the engine.
Check gaskets, replace if required. Re t drain plug
and re ll engine with clean oil.
• Replace ller cap.
Spark plug inspection
3
Disconnect the spark plug cap, and remove any dirt
from around the spark plug area.
Remove spark plug (14) with the plug spanner sup-
plied.
Inspect the spark plug. It should be a tan colour.
Measure the gap (distance contact point) with a suit-
able gauge. The gap should be 0,7 - 0,8 mm. Cor-
rect the gap, if necessary, by carefully bending the
side electrode.
Replace the spark plug if the electrodes are worn, or
if the insulator is cracked or chipped.
Install the spark plug carefully, by hand, to avoid
cross-threading.
Place the spark plug with correct torque: 20 Nm.
Attach the spark plug cap.
Air lter cleaning
Unscrew the air lter cover (18).
• Remove lter element and wash well in solvent.
Pour a small amount of oil onto the lter element and
gently squeeze out any excess oil.
• Replace the lter element and air lter cover.
Be sure the lter cover seals properly all around.
Do not run the engine without the air lter ele-
ment in place.
Never place a wet lter (with solvent) on the
machine.
Fuel tap
To remove the fuel tap lter, simply undo the cup at
the bottom of the fuel tank
Use a small spanner to remove the tap
Clean and wash out the lter and cup, and replace.
TROUBLESHOOTING
Basic checks
Make sure you have plenty of fuel
Make sure the fuel tap is on
Make sure the engine-switch is on
Make sure the oil level is correct
• Remove spark plug, connect spark plug lead and
earth it to the generator. Pull starter cord gently and
look for a spark. If there is no spark, replace spark
plug.
Spark plug is OK, but engine still won’t start
Check fuel tap lter is clean
Check fuel line is clear
Check carburetor is not clogged
Engine will not start
Clean or replace spark plug
Check ignition system – if faulty, contact your serv-
ice centre
Check compression – if low, contact your service
centre
Check for loose cylinder head – tighten bolts
Check for damaged cylinder head gasket – replace
if necessary
CLEANING
Clean the housing regularly with a soft cloth, prefer-
ably every time it is used. Keep the air vents free of
dust and dirt.
Remove stubborn dirt with a soft rag moistened in
soapy water. Do not use any solvents such as petrol,
alcohol, ammonia, etc. as such substances can dam-
age the plastic parts.
STORAGE (LONG TERM)
Drain fuel tank, fuel tap, carburetor bowl and carbu-
retor
Pour 1 cup of engine oil into the fuel tank and shake
the generator to spread the oil around the tank.
Drain excess oil.
Remove spark plug and pour in 1 spoonful of engine
oil, pull the starter cord several times with the starter
switch OFF. Replace spark plug.
Pull on the starter cord until you feel compression
and stop.
Clean the generators exterior and coat with rust in-
hibitor.
Place the generator on at ground and cover with a
clean dry cloth.
FAULTS
If a fault arises through wear in an element, please con-
tact the service address shown on the warranty card.
A drawing of the spare parts that may be obtained is
included at the end of these operating instructions.
ENVIRONMENT
To prevent damage during transport, the appliance is
delivered in a solid packaging which consists largely
of reusable material. Therefore please make use of
options for recycling the packaging.
WARRANTY
Read the terms of warranty on the separate warranty
card which is enclosed.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DPG-2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DPG-2500 in the language / languages: All languages as an attachment in your email.

The manual is 2,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info