555834
8
Zoom out
Zoom in
Previous page
1/28
Next page
8
GB
ADJUSTING CARBURETOR
IMPORTANT! A wrong adjustment may cause
damage to your unit. If the engine does not
run well after adjusting the carburetor, please
contact the shop where you purchased the product.
Idle adjustment screw
This is the screw to adjust the engine rotation when
the throttle lever is set to the lowest speed position. If
you turn right (clockwise), rotation increases, and left
(counterclockwise) decreases. In case the blade con-
tinues to rotate or engine stops when you return the
throttle lever completely to the original position, make
readjustment.
MAINTENANCE BEFORE STORAGE
1. Brushing off dirt form the machine, check damage
or slack of each part. If you nd out abnormalities,
repair them for the next use.
2. Extract fuel from the tank, and loose the drain
screw of the oat cabin to extract fuel, turn on the
engine, and leave it running until it stops naturally.
3. Remove the spark plug and put in 1-2cc of 2-cycle
oil in the engine. Draw the starter rope 2-3 times,
set the plug back, and stop it at the contraction po-
sition.
4. Apply anti-rust oil to the metal parts such as the
throttle wire, put the cover on the blade, and keep it
indoor avoiding dampness.
NOTE: This owner's manual is used for up-
per-listed machines, if slight differences from
these machines happen; the substantial ma-
chine decides the speci cation of technology and us-
age.
Fuel lter
Take the lter out of the fueling port using a small wire
hook. Disconnect the lter assembly from the fuel pipe
and unhook the retainer to disassemble it. Clean the
components with gasoline.
IMPORTANT! A clogged fuel lter may cause
poor acceleration of the engine.
Spark plug
Remove and inspect the spark plug and clean the elec-
trodes as necessary with brush.
The spark gap should be adjusted to 0.6~0.7mm.
Intake air cooling vent
Check the intake air-cooling vent and the area around
the cylinder cooling ns, and remove any waste, which
has attached itself to the brush cutter.
IMPORTANT! Note that failing to do so could
cause the muf er to become overheated, and
that this in turn could cause the brush cutter
to catch on tire.
Gear case
Supply multi-purpose grease at every 25 hours of use.
Remove the cutter holders to arrange for old grease
to exit.
AFTER 100 HOURS OF USE
Muf er
1. Remove the muf er, insert a screwdriver into the
vent, and wipe away any carbon buildup. Wipe
away any carbon buildup on the muf er exhaust
vent at the same time.
2. Tighten all screws, bolts, and ttings.
3. Check to see if any oil or grease has worked its way
in between the clutch lining and drum, and if it has
wipe it away using oil-free, lead-free gasoline.
4. Remove the oat cabin of the carburetor and clean
the inside.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DDT-1400A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DDT-1400A in the language / languages: English, French as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info