555501
7
Zoom out
Zoom in
Previous page
1/72
Next page
7
build-up of debris)
Lower guard should be retracted manually only
for special cuts such as plunge cuts and compound
cuts; raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released (for all other sawing, the lower guard
should operate automatically)
Always observe that the lower guard is covering
the blade before placing saw down on bench or
oor (an unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path;
be aware of the time it takes for the blade to stop after
switch is released)
Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them
before you start cutting
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
Use completely unrolled and safe extension cords
with a capacity of 16Amps (U.K. 13Amps)
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
• The SBM Group can assure awless functioning of
the tool only when original accessories are used
Use only accessories with an allowable speed
matching at least the highest no-load speed of the tool
Never use the tool without the original protection
guard system
This tool should not be used by people under the age
of 16 years
The noise level when working can exceed 85 dB(A);
wear ear protection
If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
Never use tool when cord is damaged; have it
replaced by a quali ed person
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
This tool is not suitable for wet cutting
After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
Never use circular saw blades made of high speed
steel (HSS)
Never use grinding/cutting discs with this tool
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
Take protective measures when during work
dust can develop that is harmful to one’s health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/
chip extraction when connectable
Do not attempt to cut extremely small workpieces
Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
Do not work overhead with the tool
Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage
Only use a saw table provided with a kerf guide
Always disconnect plug from power source
before making any adjustment or changing any
accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY):
Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
If for any reason the old plug is cut off the cord
of this tool, it must be disposed of safely and not left
unattended
Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire
is required.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations. Take
your unwanted machines to your local SBM Group
dealer. Here they will be disposed of in an environmen-
tally safe way.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DCS-181N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DCS-181N in the language / languages: All languages as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info