555500
9
Zoom out
Zoom in
Previous page
1/72
Next page
9
FR
Take protective measures when during work
dust can develop that is harmful to one’s health,
combustible or explosive (some dusts are consid-
ered carcinogenic); wear a dust mask and work with
dust/chip extraction when connectable
Do not attempt to cut extremely small workpieces
• Remove all obstacles on top of as well as under-
neath the cutting path before you start cutting
Do not work overhead with the tool
Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage
Only use a saw table provided with a kerf guide
Always disconnect plug from power source be-
fore making any adjustment or changing any ac-
cessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY):
Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
If for any reason the old plug is cut off the cord of
this tool, it must be disposed of safely and not left
unattended
Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire is
required.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots
free from dust and dirt.If the dirt does not come off use
a soft cloth moistened with soapy water. Never use
solvents such as petrol, alcohol, ammonia water, etc.
These solvents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations. Take
your unwanted machines to your local SBM Group
dealer. Here they will be disposed of in an environmen-
tally safe way.
Scie circulaire
INTRODUCTION
Cet outil est conçu pour effectuer dans le bois des cou-
pes droites longitudinales et transversales ainsi que
des angles d’onglet jusqu’à 45°; muni de lames de scie
correspondantes, il est capable de scier des matériaux
non-ferroux, des matériaux de construction légers et
des matières plastiques
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L’OUTIL 2
1. Poignée
2. Gâchette
3. Levier pour réglage de la profondeur de coupe
4. Couteau diviseur
5. Carter inférieur
6. Boulon
7. Semelle
8. Bride
9. Lame de scie
10. Guide parallèle
11. Bouton pour réglage du guide parallèle
12. Bouton pour réglage de l’angle de coupe
SECURITE
ATTENTION! Lisez toutes les instructions. Le nonres-
pect des instructions indiquées ci-après peut entraîner
un choc électrique, un incendie et/ou de graves blessu-
res sur les personnes.
DANGER
Tenez les mains éloignées de la zone de coupe et
de la lame; placez votre seconde main sur la poi-
gnée avant (si les deux mains tiennent la scie, elles
ne pourront pas entrer en contact avec la lame)
Ne placez pas la main sous la pièce (le carter ne
protège pas de la lame sous la pièce)
Adaptez la profondeur de coupe à l’épaisseur de
la pièce à travailler (il faut que moins d’une dent
complet de la denture de lame soient visible au-des-
sous de la pièce à travailler)
Ne tenez jamais la pièce à couper de la main ou
en travers de la jambe (la pièce doit être soutenue
correctement pour réduire l’exposition des parties du
corps, l’adhésion de la lame ou la perte de contrôle)
Tenez l’outil par ses surfaces antidérapantes iso-
lées lorsque vous effectuez une opération où la
zone de coupe peut entrer en contact avec des
ls cachés ou son propre cordon (si elles entrent
en contact avec un l sous tension, les parties mé-
talliques exposées de l’outil risquent d’électrocuter
l’utilisateur)
• Lorsque vous sciez, utilisez toujours un guide
parallèle (vous améliorerez la précision de la coupe
et réduirez les risques d’adhésion de la lame)
Utilisez toujours des lames de taille et forme
adéquates aux trous de montage (diamant ou
arrondi) (les lames qui ne correspondent pas à la
Français
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DCS-165N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DCS-165N in the language / languages: All languages as an attachment in your email.

The manual is 2,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info