555713
6
Zoom out
Zoom in
Previous page
1/44
Next page
6
Cordless drill/driver
INTENDED USE
This tool is intended for drilling in wood, metal, ceramic
and plastic; tools with electronic speed control and left/
right rotation are also suitable for screwdriving and thread
cutting
TECHNICAL SPECIFICATIONS 1
PRODUCT ELEMENTS 2
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
SAFETY
WARNING! Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, re and/or seri-
ous injury.
Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools that
have the switch on invites accidents.
Recharge only with the charger speci ed by the manufacturer.
A charger that is suitable for one type of battery pack may
create a risk of re when used with another battery pack.
Use power tools only with speci cally designated battery
packs. Use of any other battery packs may create a risk of
injury and re.
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before you
start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger (chargers
with a rating of 230V or 240V can also be connected to a
220V supply)
In case of electrical or mechanical malfunction, immediately
switch off the tool or unplug charger from power source
SBM Group can assure awless functioning of the tool only
when original accessories are used
Use only accessories with an allowable speed matching at
least the highest no-load speed of the tool
This tool should not be used by people under the age of 16
years
Be careful not to drill or drive into areas where electrical
wires may be contacted
Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories as
well as when carrying or storing the tool
Do not touch the contacts in the charger
Do not expose tool/charger/battery to rain
Never charge battery outdoors
Store tool/charger/battery in locations where temperature
will not exceed 40 °C or drop below 0 °C
Batteries will explode in re, so do not burn battery for any
reason
When damaged, and under extreme usage and temperature
conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly with
soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
attention
When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc. to
prevent short-circuit
Do not use charger when damaged; take it to one of the
of cially registered SBM Group Service Stations for a safety
check
• Do not use battery when damaged; it should be replaced
immediately
Do not disassemble charger or battery
Do not attempt to recharge non-rechargeable batteries with
the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire in
the cord of the charger to the earth terminal of the plug
If for any reason the old plug is cut off the cord of the charger,
it must be disposed of safely and not left unattended
To ensure longer service life and proper performance
of the battery, take the following actions when you
start using new battery:
1. Use the new battery, without recharging it, till its complete
discharge.
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth, prefer-
ably after each use. Keep the ventilation slots free from dust
and dirt.If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the plastic
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact
your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during transport,
it is delivered in a sturdy packaging. Most of the packaging ma-
terials can be recycled. Take these materials to the appropri-
ate recycling locations. Take your unwanted machines to your
local SBM Group dealer. Here they will be disposed of in an
environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal site for
chemical waste so that they can be recycled or disposed of in an
environmentally friendly manner.
English
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Defort DCD-14N-DZK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Defort DCD-14N-DZK in the language / languages: All languages as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info