Manual Day 72543 (page 44 of 121) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

789090

Zoom out

Zoom in

1/121

Initial operation:

• Insert 2- AA batteries into the rain sensor

according to polarity:

1. Press the funnel’s buckle (C1 position),

pick up the funnel and you will see the

internal rain sensor.

2. Press the sensor’s buckle (C4 position),

pick up the rain sensor, and you will see

the battery compartment below the rain

sensor.

3. Insert 2 AA batteries correctly according

to the battery polarity of the battery

compartment.

4. The sensor back into the base, and let the

buckle lock position.

• Open the battery cover of the main

device (B6 position), and correctly load

2 AA batteries according to the battery

polarity in the battery compartment.

• When you insert the batteries, all the icon

on the LCD display will brieﬂ y light up for

3 seconds, and you will hear a beep tone,

and detect indoor temperature.

• The main unit will now start to connect

to the outdoor remote sensor. This

operation will be completed in 3 minutes.

When receiving the radio signal from the

outdoor sensor, the radio signal icon will

be displayed and ﬂ ashing.

• In about 3 minutes, the main device will

automatically receive the signal from

the outdoor sensor. The rain value and

the outdoor temperature value will be

displayed on the LCD display, and the

radio icon will not ﬂ ash.

• After the master successfully receives

the signal from the remote sensor, it will

immediately exit the remote wireless

receiving mode.

Wireless sensor mounting position

1. Before installing the ﬁ xed sensor,

remove the cardboard around the rain

bucket and the tape around the rocker.

These are sensors used to protect

against accidental movement during

transportation.

2. Mount your remote sensor in an open

area for a more accurate rain count.

3. Placing the remote sensor on the ground

provides the most accurate rainfall

measurement as there is no wind shear.

Unfortunately, since insects think of

remote sensors as personal hotels,

placing your sensor 1-2 meters (3-6 feet)

above ground may deter the insects.

4. This is a self-emptying sensor, but be sure

your unit is not sitting in a depression

that would prevent rain from draining

out of the bottom

5. Your remote sensor should be accessible

to allow for periodic cleaning of leaves or

other debris that may clog the funnel.

6. Install the remote sensor on a level

platform that is stationary and has a

direct line of sight to your station.

7. Insert mounting screws through the

holes in the base of the rain sensor. Do

not over tighten.

8. Use the bubble level (C3 position) inside

your sensor to be sure it is level.

9. After securing the base of the sensor,

place the funnel section over the sensor

and make sure the buckle is locked to the

base.

10. Avoid other wireless rain sensors as

this can cause inaccuracy due to signal

interference.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Day 72543 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2.64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Day 72543 Manual

Product: