552859

Davis VANTAGE VUE Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
5
When you release the pushbutton, the LED will blink once (indicating transmitter ID 1),
then begin to flash every 2.5 seconds to show transmission of a data packet. This flashing
will stop within a few minutes to conserve battery life.
Note: If you have not already set up and powered your Vantage Vue console, do so before continuing with the
ISS installation. For best reception, the console and ISS should be at least 10 feet (3 meters) apart.
3. The console acquires the radio signal and populates data fields. This usually occurs quickly,
but in some enviromental conditions it can take up to 10 minutes.
Advanced Installations: Confirm the Transmitter ID of the ISS
Your Vantage Vue console can be used to listen to a Vantage Pro2 ISS instead of a Vantage
Vue ISS, and an optional anemometer transmitter kit.
Note: If you are using only the Vantage Vue console and ISS, and there are no other Davis weather stations
nearby, you can skip to “Verify Data from the ISS” on page 6.
In order to communicate, the console and ISS
must have the same transmitter ID. At the
factory, both IDs are set to a default of num-
ber 1. To confirm the transmitter ID of your
Vantage Vue ISS:
1. Push and release the transmitter ID
pushbutton once. It will illuminate and go
off when you release it.
2. After a short pause, it will blink one or
more (up to 8) times. Note the number of
times the transmitter ID LED blinks, indi-
cating its transmitter ID.
Unless you have intentionally changed your transmitter ID, the LED should blink one time
because the default transmitter ID for the ISS is “1.” If you have changed the ID, the LED
should blink the number of times equal to the ID you have set (i.e., twice for an ID of ‘2,’
three times for an ID of ‘3,’ etc.).
After blinking the transmitter ID, the light will begin to flash every 2.5 seconds, indicating
packet transmission.
Note: The transmitter on the ISS and receiver on the console will communicate with each other only when both
are set to the same transmitter ID.
Note: If you hold the pushbutton too long and accidentally enter the “set new transmitter ID” mode when you did
not want to, simply release the pushbutton and wait four seconds. As long as you do not press the push-
button again, the original transmitter ID will remain in effect.
Advanced Installations: Set a New Transmitter ID on the ISS
Note: In most cases, it will not be necessary to change the transmitter ID. If it is necessary to change the trans-
mitter ID, you must use the same ID for the ISS and console.
The Vantage Vue ISS transmits weather information to the Vantage Vue console using one of
eight selectable transmitter IDs. The default transmitter ID for both the ISS and the Vantage
Vue console is 1. Change the transmitter ID if another Davis Instruments wireless weather sta-
tion is operating nearby and already uses transmitter ID 1, or if you have an optional Ane-
Transmitter ID
pushbutton
Transmitter ID
LED
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Davis VANTAGE VUE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Davis VANTAGE VUE in the language / languages: English as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Davis VANTAGE VUE

Davis VANTAGE VUE User Manual - English - 56 pages

Davis VANTAGE VUE Quick start guide - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info