585987
31
Zoom out
Zoom in
Previous page
1/40
Next page
Rhino™ 10 User Manual
27
Problems with Wireless Connectivity
Problem Solution
When you turn on the Rhino™ 10 after it was sus-
pended for a while (10 to 15 minutes or longer) and
it no longer sends or receives messages over the
network.
The host may have deactivated or lost your current
terminal emulation session. In a TCP/IP direct con-
nect network, you need to turn off the “Keep Alive”
message (if possible) from the host so that the TCP
session is maintained while a Rhino™ 10 is sus-
pended.
The network connection icon in the taskbar ap-
pears to be communicating, but the host computer
is not receiving any data from the Rhino™ 10.
In a TCP/IP network, there may be a problem with
the connection between the access point and the
host computer.
Check with your network administrator or use your
access point user’s manual.
The Rhino™ 10 is not communicating with the ac-
cess point.
• The Rhino™ 10 is not connected to the access
point. Make sure the access point is turned on
and operating. You may also be using the
Rhino™ 10 out of range of an access point (no
green bars). Try moving closer to an access point
to reestablish communications.
• Make sure the Rhino™ 10 is configured correctly
for your network. The radio parameters on the
Rhino™ 10 must match the values set for all ac-
cess points the Rhino™ 10 may communicate
with.
• The radio initialization process may have failed on
the 802.11 b/g radio. Try rebooting the Rhino™
10.
• If you have tried these possible solutions and
nothing happens, you may have a defective radio
card. For help, contact Datalogic or your local
Datalogic service representative.
Upgrading the Rhino™ 10 Software
When you upgrade the Rhino™ 10 software, you are updating the operating system (OS), the Summit radio driver
and Summit Client Utility, and the Datalogic specific software.
There are three steps involved to upgrade your Rhino™ 10 computer:
1. Download the upgrade file from the Datalogic website.
2. Make the upgrade file accessible to the Rhino™ 10 computer. This can be done by;
a. Attaching a USB External storage device, such as a USB Memory Drive, USB External Hard Disk,
USB External Card reader, or using an SD Card via the existing slot under the upper left cover.
b. Downloading the file via an Ethernet connection to put the upgrade file onto the internal flash mem-
ory (Flashdisk).
c. Using a shared drive on the network.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Datalogic Rhino 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Datalogic Rhino 10 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Datalogic Rhino 10

Datalogic Rhino 10 Installation Guide - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info