Manual Dali IKON MK2 (page 8 of 38) (English, German, Danish)

562740

Zoom out

Zoom in

1/38

3.5 DALI IKON ON-WALL

DALI IKON ON-WALL is designed exclusively for wall-mounting. The front bafﬂe is tilted for optimal

angling relative to the listening position. Therefore this speaker can be positioned in four different

ways: Mounted as front, rear, or side speaker to the left or right of the listening position it will be

slightly pointed towards your listening position; mounted as a centre speaker below the TV screen

it will point slightly upwards, and mounted as a centre speaker above the TV screen it will point

slightly downwards (see ﬁgure 6). Because the loudspeaker can be positioned in four different

ways, there are four brackets on the rear panel (see ﬁgure 7). Only one of these brackets should

be used.

On the rear panel of DALI IKON ON-WALL, there are four indentations to make room for the

loudspeaker cable between the speaker and the wall. This allows you to run the cable along either

side up or down depending on what works best for you.

3.6 DALI IKON SUB

For positioning the IKON SUB, please refer to chapter 9.1.

4.0 CONNECTION

Correct, tight connections to your ampliﬁer are extremely important for your listening experience.

Always use cables of the same type and length for left and right channels. We recommend using

special speaker cables from DALI, available from your dealer.

Connection in correct phase is a detail that is often ignored. The red (+) terminal of the ampliﬁer

must be connected to the red (+) terminal of the loudspeaker. The black (-) terminal of the

ampliﬁer must be connected to the black (-) terminal of the loudspeaker (see ﬁgure 9A). Even a

single loudspeaker connected out-of-phase in a stereo or surround installation will make the bass

weaker and the stereo image unfocused.

For the optimal listening experience, the right loudspeaker (as seen from the listening position)

must be connected to the ampliﬁer output terminals marked “R” or “Right”. The left loudspeaker

must be connected to the ampliﬁer output terminals marked “L” or “Left”.

NOTE: Before connecting cables or changing any connections, ALWAYS turn off your ampliﬁer.

NOTE: Make sure that the bare conductors are tightly gripped by the terminals with no loose wires

which, could cause a short circuit and damage the ampliﬁer (see ﬁgure 8).

NOTE: If you are using DALI IKON in a surround system, follow the instructions included with your

surround ampliﬁer.

4.1 SINGLE-WIRING vs. BI-WIRING/BI-AMPING

All DALI IKON speakers can be connected by means of a single speaker cable (see ﬁgure 9A + 9B).

However, DALI IKON 2, 5, 6 and 7 are ﬁtted with two pairs of terminals, allowing you the option

of running two sets of cables to each speaker. The top terminal pair is internally connected to the

crossover network’s high frequency section. The bottom terminal pair is internally connected to

the crossover network’s bass section.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dali IKON MK2 in the language / languages: English, German, Danish as an attachment in your email.

The manual is 3,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dali IKON MK2

Dali IKON MK2 User Manual - English - 38 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dali IKON MK2 Manual

Product: