643443
25
Zoom out
Zoom in
Previous page
1/1009
Next page
(4) Cleaning of air filter element
Clean the air filter element with compressed air.
First, blow compressed air from the back side of the
element thoroughly. Then, blow off the upper side of
the element.
WARNING:
· Protect your eyes with safety goggles during the clean-
ing operation.
CAUTION:
· The air pressure to be used for this cleaning operation
should not exceed 392.3 kPa (4.0 kgf/cm
2
).
Replace the air filter element, if the element is exces-
sively dirty.
(5) Installation of air filter element
q Install the air filter element in the air filter case cover.
NOTE:
· Ensure that the air filter element faces in such a direc-
tion that the wider protrusion side comes to the air filter
case cover side.
w Close the air filter case cover.
e Latch the four clips properly.
3. Inspection of blow-by gas recirculation device
(1) Visually inspect the hoses for improper connections,
cracks, leak and damage.
NOTE:
· Replace parts which exhibit damage as necessary.
(2) Remove the oil filler cap.
(3) Disconnect the blow-by gas hose from the throttle
body.
(4) Ensure that no resistance exists when you blow your
breath to the disconnected hose end (which was con-
nected to the throttle body).
If resistance is felt or no air continuity exists, check
blow-by gas hose and the cylinder head cover.
(5) Connect the blow-by gas hose to the throttle body.
(6) Install the oil filler cap securely.
(7) Disconnect the PCV hose which is connected to the
throttle body at the throttle body side.
(8) Ensure that heavy resistance exists when you blow
your breath from the disconnected hose end.
If no continuity exists or no resistance for air continuity
exists, replace or repair the cylinder head cover.
(Refer to the EM section for the cylinder head cover re-
placement.)
NOTE:
· The orifice is built in the cylinder head cover. This pro-
cedure is required for ensuring the orifice function in
the cylinder head. If this orifice is plugged, correct en-
gine idle speed will not be obtained.
(9) Connect the PCV hose to the throttle body properly.
MA–7
JMA00008-00004
JMA00009-00005
JMA00010-00006
JMA00011-00007
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Daihatsu Terions J100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Daihatsu Terions J100 in the language / languages: English as an attachment in your email.

The manual is 41,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info