Manual Dahua IPC-PFW8601-A180 (page 15 of 17) (English)

670274

Zoom out

Zoom in

1/17

Dahua HD IR Panoramic Bullet Network Camera

Quick Start Guide

Version 1.0.0

Zhejiang Dahua Vision Technology Co., LTD

Welcome

Thank you for purchasing our Network camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual well for future reference!

Important Safeguards and Warnings

1．Electrical safety

 All installation and operation here should conform to your local electrical safety codes.

 Please check if the power supply is correct before operating the device.

 The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated AC 24V in the IEC60950-1. (Power supply requirement is subject to

the device label).

 Please install easy-to-use device for power off before installing wiring, which is for emergent power

off when necessary.

 Please prevent the line cord from being trampled or pressed, especially the plug, power socket and

the junction from the device.

 Note: Do not connect these two power supplying sources to the device at the same time; it

may result in device damage!

 We assume no liability or responsibility for all the fires or electrical shock caused by improper

handling or installation.

 We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Environment

 Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus; otherwise

it may cause overexposure (It is not the device malfunction), which will affect the longevity of CCD

or CMOS.

 Please transport, use and store the device within the range of allowed humidity and temperature.

 Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and

with strong electromagnetic radiation or unstable lighting.

 Please do not allow water and other liquid falling into the camera in case that the internal

components are damaged.

 Please do not allow rain or damp to the indoor device in case fire or lightning may occur.

 Please keep the sound ventilation in case of heat accumulation.

 Please pack the device with standard factory packaging or material with same quality when

transporting the device.

 Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3. Operation and Daily Maintenance

 Please do not touch the heat dissipation component of the device directly in order to avoid scald.

 Please do not dismantle the device; there is no component which can be fixed by users themselves

in the machine. It may cause water leakage or bad image for the device due to unprofessional

dismantling. Please contact after-sale service to replace desiccant if it becomes green.

 It is recommended to use the device with thunder proof device in order to improve thunder proof

effect.

 The grounding holes of the product are recommended to be grounded to further enhance the

reliability of the camera.

 Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean the dust

or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if

it is necessary to clean.

 Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean

the device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or strong detergent with

abrasiveness, otherwise it will damage the surface coating or reduce the working performance of

the device.

 Dome cover is an optical device, please don’t touch or wipe cover surface directly during

installation and use, please refer to the following methods to deal with once dirt is found:

 Stained with dirt

 Use oil-free soft brush or hair dries to remove it gently.

 Stained with grease or fingerprint

 Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth or

paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to change

the cloth and wipe several times if it is not clean enough.

Warning

 Please modify the default password after login in order to avoid being stolen.

 Please use the standard accessories provided by manufacturer and make sure the device is

installed and fixed by professional engineers.

 Please prevent the device surface from the radiation of laser beam when using laser beam device.

 Please do not provide two or more power supply modes for the device, otherwise it may cause

damage to the device.

Statement

 Please refer to the actual product for more details; the manual is just for reference.

 The manual will be regularly upgraded according to the product update; the upgraded content will

be added in the manual without prior announcement.

 Please contact the supplier or customer service if there is any problem occurred when using the

device.

iii

 Please contact the customer service for the latest procedure and supplementary documentation.

 There may be deviation between the actual value of some data and the value provided in the

manual due to the reasons such as the real environment is not stable and so on. Please refer to

the company’s final explanation if there is any doubt or dispute.

 The company is not liable for any loss caused by the operation which is not followed by the manual.

Note:

Please refer to the disk for more details, check and download corresponding user’s manual and tool.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

Table of Contents

1 Device Structure ......................................................................................................................... 1

1.1 Device External Cable ................................................................................................. 1

1.2 Framework and Dimension ......................................................................................... 2

1.3 Alarm Setup ................................................................................................................... 2

2 Device Installation ...................................................................................................................... 5

3 Network Configuration ............................................................................................................... 9

3.1 Modify IP Address ........................................................................................................ 9

3.2 Login WEB Interface .................................................................................................. 10

1 Device Structure

1.1 Device External Cable

Note:

The following figure is for reference only, which is used to know the function of cable port.

You can refer to the following figure for cable information. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

No.

Port

Name

Function

Connector

Note

AUDIO

OUT

Audio

output port

RCA

Output audio signal to speaker and etc.

AUDIO

Audio input

port

RCA

Input audio signal, receive analog audio signal from

pickup and etc.

LAN

Network

port

Ethernet

port

Connect to standard Ethernet cable.

Note: Some series don’t support PoE.

I/O

I/O port

Alarm signal input/output. Please refer to sheet 1-2 for

more details.

Power

Power input

port

Power port. Input DC 12V or AC 24V power.

Note:

 Please connect the DC5.5 round port to 2-pin

converter cable when you are using AC 24V

power.

 Please use according to device tag.

Sheet 1-1

Please refer to sheet 1-2 for details about port function. .

Port Name

Name

Note

I/O Port

ALARM_OUT

Alarm output port. It is to output the alarm signal to the

alarm device.

ALARM_OUT_GND

ALARM_IN1

Alarm input port 1. It is to receive the on-off signal from the

external alarm source.

ALARM_IN2

Alarm input port 2. It is to receive the on-off signal from the

external alarm source.

ALARM_IN_GND

Alarm input ground port

Sheet 1-2

1.2 Framework and Dimension

Note:

The following figure is for reference only, which is used to know the device dimension.

Please refer to the following figure for dimension information. The unit is mm. See Figure 1- 2.

Figure 1-2

1.3 Alarm Setup

Note:

It is only supported by some series products.

Figure 1-3

Alarm input, output connection description:

Step 1

Connect alarm input device to the alarm input of I/O port cable.

Step 2

Connect alarm output device to the ALARM_OUT and ALARM_OUT_GND of I/O port cable,

Alarm output is the relay switch output; alarm output port can only be connected to NO (normally

open) alarm device.

Step 3

Open the WEB, set alarm input and output correspondingly in alarm setup. Alarm input on the

WEB is corresponding to that of the device I/O port cable. When there is alarm, alarm input

device will generate signal of high and low level. Set corresponding NO and NC inputs.

Step 4

Set alarm output on the WEB, the alarm output is corresponding to the alarm output end of the

device, this is the alarm output port of the I/O port cable.

Please refer to the following figure for alarm input and output information. See Figure 1-4.

Alarm input: When the input signal is idle or grounded, the device can collect the different

statuses of the alarm input port. The input signal is connected to 3.3V or it is idle; the device

collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 1-4

Alarm output: port ALARM_OUT and ALM_OUT_GND form a switch, which is used to provide

alarm output. Normally the switch is on; it will be off when there is alarm output.

Figure 1-5

2 Device Installation

Note:

 Please make sure the installation surface can min support the 3X weight of the camera and

the bracket.

 Please cut off the power before installing Micro SD card.

Figure 2-1

Step 1

SD card installation (Optional)

Note:

It needs to implement the step if there is a SD card slot in the device and it needs to use the SD

card.

You can see the SD installation card slot, analog video output port and reset button after you

open the lower cover.

Insert the SD card into the slot which is shown in Figure 2-2, you can press the SD card slightly

to insert it because the card slot is elastic.

Figure 2-2

Note:

 You can connect the analog output port to the TV monitor to check image via analog output

cable.

 Press the reset button for 4 to 5 seconds to realize reset function for the device.

Step 2

Stick the installation position map on the designated surface where you will install the device

(wall or ceiling), then dig holes according to hole location marked on installation map.

Step 3

Open the accessories bag, take out expansion bolts and insert them into the hole you just dug.

Step 4

Open the accessories bag, take out screws. Tighten the 4 screws to fix the device on the

installation surface (wall or ceiling). You can move the device sunshield back and forth. When

you have fixed the device, you must tighten screws on sunshade.

Step 5

Plug the external cables of the device properly according to the use requirements.

Step 6

Adjust the monitoring direction of the device.

Note:

 Please be sure to loosen the adjusting screws when adjusting the device position and angle,

tighten the adjusting screws after adjustment.

 The continuous rotation toward the same direction for the camera body has to be no more

than 3 circles.

 The lower cover can’t be opened for a long time, besides; it can’t be opened in the humid

environment in case water mist and fog problem may happen to the device.

Figure 2-3

1. Use screwdriver to loosen adjusting screws.

2. Adjust the device in all possible directions, and set its monitoring direction according to use

requirement.

3. Use screwdriver to tighten the adjusting screws.

Step 7

Waterproof connector installation for network port; see Figure 2-4 for more details.

Note:

Please implement this step if the device is equipped with network port waterproof connector and

it is used outdoors.

Figure 2-4

1. Keep the convex groove outward and install the rubber ring into the network port, keep the

smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of

the waterproof connector.

2. Pull the network cable without crystal head through main body of waterproof connector, fixing

rubber ring and waterproof locking cover, make the crystal head of network cable, and then

insert it into the network cable.

3. Put the main body of waterproof connector on the network port and rotate it clockwise to lock

the network port and waterproof connector firmly.

4. Put the waterproof locking cover on the main body of waterproof connector and rotate it

clockwise to lock the waterproof connector and waterproof locking cover firmly.

3 Network Configuration

The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in

order to make the camera get access to the network smoothly, please plan the useable IP

segment reasonably according to the actual network environment.

3.1 Modify IP Address

IP address can be acquired and modified through quick configuration tool for the cameras which

are accessed via wired network, it needs to connect wired network to configure wireless

parameters before using wireless network cameras. In this chapter, it will introduce the approach

of modifying IP address via “Quick Configuration Tool”; also you can modify the IP address in the

network parameters of the WEB interface, please refer to the document in the disk << WEB

Operation Manual>> for more details.

Note:

Currently the quick configuration tool only supports the cameras which apply to the same

network segment with computer IP address.

Step 1 Double click the “ConfigTools.exe” and open the quick configuration tool.

Step 2 Double click the device to be configured, the system will pop out the “Login” dialog box.

Enter the IP address, user name, password and port number of the camera, and click

“Confirm”.

Note:

The default user name and password are admin and admin respectively, the default of port is

37777. See Figure 3-1 for more details.

Figure 3-1

Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finish modification.

See Figure 3-2 for more details.

Figure 3-2

3.2 Login WEB Interface

Note:

Different devices may have different WEB interfaces, the figures below are just for reference,

please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for

more details

Step 1 Open IE and input the modified camera IP address in the address bar.

Step 2 The login interface is shown below, please input your user name and password (Default

user name is admin and password is admin respectively), click “login”.

See Figure 3-3 for more details.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dahua IPC-PFW8601-A180 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dahua IPC-PFW8601-A180

Dahua IPC-PFW8601-A180 User Manual - English - 144 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dahua IPC-PFW8601-A180 Manual

Product: