445546

Daewoo DSJ4720 Manual

22
Zoom out
Zoom in
Previous page
1/97
Next page
21
Explanation for circuit operation
When B+ 135V is supplied and +5V is applied, approx. 31KV high voltage and 11.6KV focus
voltage are generated automatically. If EHT of HVG is outputted more than 35KV, HVG
module starts over voltage protection to stop the high voltage.
5) Spot killer components
Approx. -220V voltage made by using HVG high voltage output voltage is supplied from HVG
PIN4, rectified and smoothed to D819 and C425 and used as spot killer power. After this
power is divided into R448 and R449 normally, a voltage near to -20V via R465 is supplied
for CRT board GRID 1 via connector PA13 G1. But, at first AC power ON, the spot killer
signal supplied via a connector PA15M in main board is provided for the base of Q412. At
AC power OFF, a voltage near to -220V via Q414 is provided for GRID 1 of CRT board via
G1 of connector PA16M. As a result, the screen gets dark to prohibit the generation of a
spot.
6) Dynamic focus voltage generator
The dynamic focus voltage provides a parabola waveform conforming to CRT spec.
(horizontal:1000V, vertical:200V) for CRT to make the focus of 7” CRT optimum. A D/F
waveform from 1403 pin32 is amplified approx. 100 times in an amplifying circuit composed
of OP AMP and a parabola waveform is amplified approx. 1000Vp-p in an amplifying circuit
composed of QF11, 12, 13. Then, they are input to QF14 base. The horizontal waveform of
1300Vp-p left in T402 terminal No.16 is rectified and smoothed to DF13, 12, RF17, CF11, 12
and supplied for QF14 collector as B+ for dynamic focus.
7) ABL input part
The ABL current supplied from main board via the ABCL terminal of a connector PA401
flows in via FBT PIN2. Then, the current amount is detected, the BCL circuit is operated in
the main board and the maximum current amount is controlled. If a beam current begins to
flow about 1.5mA, the ABL circuit will work and if about 1.8mA, the ABL feedback circuit will
work. Therefore, be careful not to be more than 1.8mA.
8) VM (Velocity Modulation) outline correction part
The outline correction circuit is operated in exclusive correction IC, IV11 (STK396-130). The
VM waveform made in the main PCB is input to the deflection PCB PA401 PIN1. The input
1Vp-p signal is input to IV11 PIN1. The input signal is amplified about 100 to 120Vp and
output to IV11 PIN9. Then, it is input to IV11 PIN10 via the circuit composed of VM coil PV11,
12, 13. The power of +12V and +135V GND are used.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Daewoo DSJ4720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Daewoo DSJ4720 in the language / languages: English as an attachment in your email.

The manual is 9,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info