486204
51
Zoom out
Zoom in
Previous page
1/72
Next page
50
Timer Recordings
TIMER RECORDINGS USING ShowView
For timer recordings, clock, date, and stations must be set correctly.
Load a cassette with its safety tab in place and with sufficient free space for the recording.
Call the ShowView menu by pressing PROGRAM on the
remote control.
From your TV magazine, type in the number next to the programme you
want to record ...
... and confirm.
1
Decide if you want to record "ONCE", "WEEKLY" or "DAILY"...
... and confirm.
2
If you wish to make changes:
Move to the position you want to change using the [
œ/
] buttons.
Change the setting using the [/] or [number] buttons. If all setting
are ok, press [ok], till you see “OK: CONFIRM” in the bottom line.
Confirm.
3
Switch your player off.
0-9:SHOWVIEW NUMBER
œ :CORRECT
OK:CONFIRM SETUP:END
SHOWVIEW
83077----
HOW OFTEN DO YOU WANT
TO RECORD THIS PROGRAM?
/:SELECT
OK:CONFIRM SETUP:END
TIMER PROGRAM (ONCE)
PR 03
START TIME 21:20
END TIME 22:20
START DATE 14/06(SAT)
TAPE SPEED SP
VPS/PDC ON
/:SELECT (AV1/AV2)
0-9 : SETUP (PR)
œ/:CORRECT
OK:CONFIRM SETUP:END
ONCE
WEEKLY(ONCE A WEEK)
DAILY(MON-FRI)
DAILY(MON-SAT)
DAILY(MON-SUN)
VPS/PDC is a service provided by some stations to enable you to perform timer recordings precisely even if
the broadcaster delays the start time of the programme slightly. The time you enter is the VPS/PDC time so
must be correct. Not all stations offer VPS/PDC, in which case the player will start at the time you enter and
not the actual start time of the programme.
If you wish to start recording at a specific time without it being adjusted by the VPS/PDC system in the
event of a delay, switch VPS/PDC off otherwise the player will not record.
If you don’t have the ShowView numbers see next page for the normal timer.
If you have made a mistake, move back to the relevant position with the [
œ
] button and change the setting.
If there is no programme location displayed under “PR” in the change menu, the player doesn’t yet know
the location number for the programme you want. Type it in and this will be stored for last recordings.
If you wish to record from a satellite receiver, select under “PR” the satellite programme location or AV (1/2)
(depending on the connection with the antenna cable or the SCART-cable). Leave the satellite tuner
switched on and to the programme you want.
Should programming overlap, you get a warning.
To cancel the recording press the button (stop) more than 5 seconds.
ShowView is a trademark applied for by Gemstar Development Corp.. The ShowView system is
manufactured under license from Gemstar Development Corporation.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Daewoo DCR-9120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Daewoo DCR-9120 in the language / languages: English as an attachment in your email.

The manual is 5,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info