728143
111
Zoom out
Zoom in
Previous page
1/136
Next page
Unied Access Point Administrator’s Guide
Unied Access Point Administrator’s Guide
Page 111
October 2017
Section 9 - Clustering Multiple APs
Field Description
Cluster-Controller This is supported only for IPv4. It species which member access point is “Dominant”.
If cluster member is dominant, the cluster controller eld shows “yes”; if not, it will display
“no” in the table.
Note: Currently, this eld is available only in DWL-3610AP and DWL-6610B1AP.
Table 63 - Access Points in the Cluster
Cluster Options
The following table describes the cluster information to congure for an individual member. The clustering options are
read-only when clustering is enabled. To congure the clustering options, you must stop clustering.
Field Description
Location Enter a description of where the access point is physically located.
Cluster Name Enter the name of the cluster for the AP to join.
The cluster name is not sent to other APs in the cluster. You must congure the same cluster
name on each AP that is a member of the cluster. The cluster name must be unique for each
cluster you congure on the network.
Clustering IP
Version
Specify the IP version that the APs in the cluster use to communicate with each other.
Cluster-Priority This is supported only for IPv4. Species the Priority of the cluster member and is
congurable by user. The higher number indicates the higher preference for this AP to
become the dominant AP. In case of tie, lowest MAC address becomes dominant. Range: 0
to 255. Default value is 0.
Note: Currently, this eld is available only in DWL-3610AP and DWL-6610B1AP.
Table 64 - Cluster Options
Single IP Management
The following table describes to congure Single IP Management.
Field Description
Cluster
Management
Address
This is supported only for IPv4. In order to access the cluster with a single IP, the cluster can
be congured with an option of Cluster IP address. This is a part of the global conguration
of the cluster in section. It has to be statically congured by the Cluster Administrator. The
Cluster IP management address should be part of the same subnet as the clustered AP
management IP addresses. The Cluster IP address is congured as secondary IP address
to the management interface of the Dominant AP. The Dominant AP user interface is
accessible using the Cluster IP address. When the Cluster IP address is set as secondary
IP address on the Dominant AP, it sends Gratuitous ARPs on the management VLAN so that
the mapping between the new IP address and the Mac-address is established in the subnet.
The Cluster IP address conguration is shared among all the clustered APs.
Table 65 - Single IP Management Options
Secure Join Clustering
The following table describes to congure Secure Join Clustering. This is supported only for IPv4.
Field Description
Secure Mode Conguration parameter to enable/disable Secure Join Clustering. When enabled only
members with same pass-phrase will form the cluster. Default value id Disable.
111


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for D-Link DWL-6700AP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of D-Link DWL-6700AP in the language / languages: English as an attachment in your email.

The manual is 7,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info