541876
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
2.2: To allow enough space for your bike to fit into the trainer, rotate the yellow
skewer clamp so it is fully retracted into the trainer frame.
2.2: Gire el pomo amarillo de la mordaza de la abrazadera en el sentido de las
agujas del reloj para dejar espacio suficiente al cierre rápido.
2.2: Tournez le bouton de serrage de la broche (jaune) dans le sens des aiguilles
d’une montre afin de ménager un écartement suffisant pour votre broche.
2.2: Drehen Sie den gelben Drehknopf im Uhrzeigersinn, um ausreichend Platz für
den Schnellspanner zu erhalten.
2.2: Ruotare la manopola gialla del perno completo di meccanismo di chiusura in
senso orario in modo da fornire spazio sufficiente al perno.
2.2: Draai de gele knop van de penklem in de richting van de wijzers van de klok om
voldoende ruimte vrij te laten voor de ontgrendelingspen.
2.2: 黄色のブを時計方向にーに十分
な隙間を空け
4.6: Scroll down to Sensor ID and manually add the sensor ID number on your
resistance unit.
4.7: Once ID is properly inputted scroll and select Activate Sensor to complete
manual pairing.
Note: Bike with activated RU sensor must be your current activated bike denoted
with a check on the bike menu screen.
4.6: Desplácese hasta “Sensor ID” (Id. de sensor) y añada manualmente el número
de Id. del sensor en la unidad de resistencia.
4.7: Una vez correctamente introducido el Id. desplácese y seleccione “Activate
Sensor” (Activar sensor) para completar el emparejamiento manual.
Nota: la bicicleta con sensor de RU activada debe ser la bicicleta activada
actualmente lo que se indica con una marca de comprobación en la pantalla de
menú de la bicicleta.
4.6: Faites défiler l’écran jusqu’à Sensor ID (ID du capteur) et ajoutez manuellement
le numéro d'ID à votre unité de résistance.
4.7: Faites ensuite défiler l’écran et sélectionnez Activate Sensor (Activer le capteur)
pour terminer le couplage manuel.
NB : le vélo dont le capteur d'unité de résistance est activé doit être le vélo actif,
marqué d'une coche sur l'écran de menu du vélo.
4.6: Scrollen Sie nach unten zur Sensor-ID und fügen Sie die Sensor-ID-Nummer
auf Ihrer Widerstandseinheit manuell hinzu.
4.7: Sobald die ID richtig eingegeben ist, wählen Sie „Sensor aktivieren“, um die
manuelle Kopplung abzuschließen.
Hinweis: Das Fahrrad mit aktiviertem RU-Sensor muss Ihr zurzeit aktiviertes
Fahrrad sein, das auf dem Fahrradmenübildschirm mit einem Häkchen markiert ist.
4.6: Blader naar beneden tot aan Sensor ID en voeg manueel het ID van de sensor
op uw weerstand toe.
4.7: Zodra het ID is ingegeven, bladert u naar en selecteert u Activate Sensor om
het manuele koppelingsproces te vervolledigen.
Opmerking: Fiets met een actieve RU sensor moet de fiets zijn die op dit ogenblik
actief is en die is aangevinkt in het fietsmenu.
4.6: Scorrere sino a Sensor ID [ID sensore] e aggiungere manulamente il numero ID
del sensore sull'unità di resistenza in uso.
4.7: Una volta adeguatamente inserito l'ID, scorrere e selezionare Activate Sensor
[Attiva sensore] per completare il collegamento manuale.
Nota: La bici con sensore RU attivato deve essere la bici attivata al momento e cioè
contrassegnata con una spunta sulla schermata del menu della bici stessa.
4.6: ID (センサ ID) までクロ ユーザーの負荷ユニ
にセンサー ID 号を追加ます
4.7ID 正しく力しら、Activate Sensor (ンサーの起動) までスク
ローて選し、ペアグを完了させます
注:RU ンサーがアになているバイは、バイ メニュ
面においで示されるユーザーの現在のブに
るバイ一致している必要ます
RU Sensor
Activate Sensor
Start Pairing
Name
RU 1
Sensor ID
00111
9:34A
RU Sensor
Activate Sensor
Start Pairing
Name
RU 1
Sensor ID
00111
9:34A
4
LED Function
The PowerBeam has a blue LED located between the flywheel and RU to
communicate what state the product is in. Below are the different states of
communication between the RU and PC or display unit.
Flashing LED – Ready, but not connected to PC or display.
LED On – Communicating with PC or display.
LED Off – Sleep mode or Off. – Spin wheel or plug in to activate.
Función LED
El PowerBeam dispone de un LED azul ubicado entre la rueda y la RU para
comunicar en qué estado está el producto. Debajo se indican los diferentes estados
de comunicación entre la RU y el PC o unidad de pantalla.
LED parpadeante: lista, pero no conectada al PC o pantalla.
LED encendida: comunicación con el PC o pantalla.
LED apagado – Modo suspensión o desactivación. – Gire la rueda o conecte para
activar.
Fonction LED
Le PowerBeam est pourvu d'une LED située entre le volant d'inertie et l'unité de
résistance, afin d'indiquer l'état de l'appareil. Les divers états de communication
entre l'unité de résistance et le PC ou la console d'affichage sont les suivants :
LED clignotante – Prêt, mais non connecté au PC ou à la console d'affichage.
LED allumée – Communication avec le PC ou la console d'affichage.
LED éteinte – Mode veille ou éteint. – Faites tourner la roue ou branchez l'appareil
pour l'activer.
LED-Funktion
Beim PowerBeam befindet sich eine blaue LED zwischen Schwungrad und RU, die
mitteilt, in welchem Zustand sich das Produkt befindet. Unten finden Sie die
verschiedenen Kommunikationszustände zwischen RU und PC oder Anzeigeeinheit.
Blinkende LED – bereit, aber nicht mit dem PC oder Display verbunden.
LED ein – Kommunikation mit dem PC oder Display.
LED aus – Ruhezustand oder aus. – Zum Aktivieren Rad drehen oder anschließen.
LED-functie
De PowerBeam heeft een blauwe LED die zich tussen het _ywheel en de RU
bevindt en de status van het product communiceert. Onderstaand overzicht geeft
de verschillende communicatiestatussen weer tussen de RU en de PC of
weergavescherm.
Knipperende LED - Klaar, maar nog niet verbonden met PC of weergavescherm.
Funzione LED
Il PowerBeam presenta un LED blu che si posiziona tra volano e RU per comunicare
lo stato in cui si trova il prodotto. Seguono i diversi stati di comunicazione tra RU e il
PC o l'unità di visualizzazione.
LED lampeggiante - Pronto, ma non connesso a PC o display.
LED On/acceso - Comunicazione in corso con PC o display.
LED Off/spento – Modalità di riposo o spento. – Far girare la ruota o collegare per
attivare.LED aan - Communicatie met PC of weergavescherm is succesvol.
LED O_ – Slaapstand of O_. – Draai aan het wiel of sluit aan om te activeren.
LED 機能
PowerBeam は、フライイールと RU の間に、製品の状態を知
ための青色 LED いていますRU PC またはデスプレ ニッ
間の通信の各種状態は以下の通です
LED 点滅 – Ready (準備完)PC または レイには未接続。
LED On (オン) – PC また スプレと通
LED Off (オフ) – Sleep ード (スリープ ード) または Off( オフ) – ホイ
ールを回転させか、またはプラグを差込ん起動。
4.6
6
4.7
6
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cycle Ops PowerBeam Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cycle Ops PowerBeam Pro in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info