767426
37
Zoom out
Zoom in
Previous page
1/174
Next page
37
DEENIT
REMOVING THE SEAT COVER RIMOZIONE DEL RIVESTIMENTO
NOTE! Before removing the separate parts of the seat cover,
please ensure that the cover is already positioned above the
decorative silver parts. To put the covers back on the seat,
proceed as above in reverse order. Make sure that the green
belt guide (21) always rests visible above the seat cover.
NOTA BENE! Prima di rimuovere le varie parti del rivestimento
vericare che le estremità siano già state estratte dalle parti
decorative argentate. Per riposizionare il rivestimento sul
seggiolino, ripetere i passaggi precedentemente descritti
nell’ordine inverso. Assicurarsi che la guida verde della cintura
(21) sia sempre visibile sopra il rivestimento del seggiolino.
The seat cover consists of ve parts which are xed to the
seat with velcro, press studs or button holes. One you have
released the fasteners, the cover parts can be removed. To
remove the covers, please follow the instructions below:
Take o󰀨 the “Linear Side-Impact Protection” System
(L.S.P.) by pushing it upwards to release it from its
anchorage points.
Undo the press studs on the lower side of the cover for
the adjustable headrest. Then you can remove the cover
upwards.
Activate the adjustment handle for the headrest and move
this to its highest position.
Open and loosen all the press buttons on the rear side of
the headrest. Then pull the cover o󰀨 forwards.
Pull down the cover on the left and right side panel of the
shoulder rest. Then undo the press studs on the interior of
the shoulder wings in order to be able to entirely remove
the cover.
Before you can remove the backrest cover from the seat,
undo the associated fastenings its rear side.
Then thread the elastic bands out on the underside of the
seat area, and withdraw the seat cushion cover forwards.
Il rivestimento è composto da cinque parti ssate alla scocca
con velcro, bottoni a pressione o asole. Una volta sganciati tutti i
punti di ssaggio è possibile rimuovere ciascuna delle parti per il
lavaggio. Per rimuovere il rivestimento eseguire i seguenti passaggi:
Per rimuovere il sistema di protezione lineare negli impatti
laterali (Linear Side-Impact Protection, L.S.P.) spingere
verso l‘alto per staccarlo dai punti di ancoraggio.
Sganciare i perni a pressione sul lato inferiore del
rivestimento del poggiatesta regolabile. Rimuovere il
rivestimento verso l’alto.
Attivare la maniglia di regolazione del poggiatesta e
spostare quest’ultimo nella posizione più alta.
Aprire e allentare tutti i bottoni a pressione nella parte posteriore
del poggiatesta. Quindi togliere il rivestimento tirandolo in avanti.
Tirare verso il basso il rivestimento su ambo i lati del
pannello destro e sinistro della protezione per le spalle.
Quindi slacciare i bottoni automatici nella parte interna delle
ali di protezione per le spalle in modo da poter rimuovere
completamente il rivestimento.
Per rimuovere il rivestimento dello schenale dal seggiolino
è necessario slacciare tutti gli agganci associati nella sua
parte posteriore.
Quindi slare le fascette elastiche sul lato inferiore dell’area
seduta e tirare il rivestimento seduta in avanti.
!WARNING! The infant car seat must under no
circumstances be used without the cover. !ATTENZIONE! Non usare MAI il seggiolino di sicurezza
senza il rivestimento.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cybex SOLUTION Z i-FIX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cybex SOLUTION Z i-FIX in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 6,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info