768272
10
Zoom out
Zoom in
Previous page
1/92
Next page
7
EN
CORRECT INSTALLATION MODE
Group 1

Group 2/3

Installation mode with impact shield without impact shield
Installation

1. Insert the impact shield (f)(f)
between the arm rests and seating surface of the booster.
2. Pull out the entire length of the vehicle seat belt.
3. Place the lap belt over the designated red belt routing on the impact shield (g).
4. Lock the vehicle seat belt into the belt buckle. It must lock in place with an
audible “CLICK”.
5. Tighten the lap belt by pulling the shoulder belt backwards.
6. Feed the shoulder belt in parallel with the lap belt back into the belt routing
(g) and pull the shoulder belt tight. Ensure that both parts of the belt cover
the entire width of the impact shield (f) in the belt routing (g).
7. Feed the shoulder belt tightly through the belt routing of the impact shield (g)
until it is clamped inside the belt guide.
8. Put the shoulder belt between headrest (c) and backrest (b). The shoulder
belt does not need to be guided through the shoulder belt guide (i).
SWITCH FROM GROUP 1 TO GROUP 2/3
Remove the impact shield (f), as soon as your child weighs 18 kg.
💡Note that switching from group 1 to group 2/3 is not permitted if your
child weighs less than 15 kg. Keep the impact shield in a safe and
secure place.
SECURING THE CHILD WITHOUT IMPACT SHIELD – GROUP 2/3

1. Route the vehicle seat belt around your child and insert the belt tongue into
the belt buckle. It must lock into place with an audible "CLICK".
2. Place the lap belt in the red coloured lap belt guides (h) of the child seat.
3. Pull the shoulder belt to tighten the lap belt.
4. On the side of the car seat next to the belt buckle, the shoulder belt and the
lap belt must be inserted together in the lap belt guide (h).
5. Feed the shoulder belt through the shoulder belt guide (i) until it is inside
the belt guide.
6. Ensure that the shoulder belt runs across your child’s clavicle and does not
touch your child’s neck. If necessary, adjust the height of the headrest (c) to
change the position of the belt.
REMOVING AND REATTACHING THE SEAT COVER
The cover of the child seat consists of four parts (headrest, backrest, booster
and impact shield). These are held in position at several places by press-
studs. Once all studs have been released, the single parts of the cover can
be removed.
In order to put the covers back on the seat, follow the removal instructions in
the reverse order.
💡The cover may only be washed at 30 °C with a delicate wash program
otherwise it may result in discolouration of the cover fabric. Please wash
the cover separately from other laundry and do not dry in the dryer or in
direct sunlight!
WARRANTY AND DISPOSAL REGULATIONS
CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you
3 years warranty on this product. The warranty is valid in the country, where
this product was initially sold by a retailer to a customer. The contents of
the guarantee and all essential information required for the assertion of the
guarantee can be found on our homepage www.cybex-online.com. If a
warranty is shown in the article description, your legal rights against us for
󰀨
Please observe the waste disposal regulations in your country.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cybex Pallas B2-Fix plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cybex Pallas B2-Fix plus in the language / languages: All languages as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info