817300
357
Zoom out
Zoom in
Previous page
1/404
Next page
Wheels and tyres
355
Changing a wheel
Fig.238 Crossbar: mounting the jack on
the vehicle.
Rest the jack (vehicles tools) on rm ground.
If necessary use a large, strong board or similar
support. If the surface is slippery (for example
tiles) place the jack on a rubber mat or similar
to prevent it from slipping ››› .
Look on the strut for the mark of the jack
support point (sunken area) closest to the
wheel to be changed ›››Fig.237.
Turn the jack crank handle, located below
the strut support point, to raise it until the
tab 1 ›››Fig.238 is below the housing that
is provided.
Align the jack so that the tab 1“grips”
onto the housing provided on the cross mem-
ber and the mobile base 2 is resting on the
ground. The base plate 2 should fall vertically
with respect to the support point 1 .
Continue turning the jack until the wheel is
slightly lifted o the ground.
WARNING
The factory-supplied jack is only designed
for changing wheels on this model. On no
account attempt to use it for lifting heavier
vehicles or other loads. Risk of injury.
Make sure the jack remains stable. If the
surface is slippery or soft, the jack could slip
or sink, respectively, with the consequent
risk of causing injuries.
Lift the vehicle using only the jack supplied
from the factory. Other jacks, even those ap-
proved for other CUPRA models could slip,
with the consequent risk of injury.
Place the jack only at the support points
provided on the strut and align it. Otherwise,
the jack could slip because it does not have
suicient grip on the vehicle: risk of injury!
You should never place a body limb such as
an arm or leg under a raised vehicle that is
solely supported by the jack.
If you have to work underneath the vehi-
cle, you must use suitable stands additionally
to support the vehicle, there is a risk of acci-
dent!.
Never raise the vehicle if it is tilting to one
side or the engine is running.
Never start the engine when the vehicle is
raised. The vehicle may come loose from the
jack due to the engine vibrations.
NOTICE
The vehicle must not be raised on the
crossbar. Place the jack only at the support
points provided on the strut and align it. Oth-
erwise, the vehicle may be damaged.
Any type of load or weight applied to the
external trim/door will (stepped on, tting
the jack, resting heavy objects, etc.) can
cause damage to it. CUPRA accepts no re-
sponsibility for any damages caused by im-
proper use of the external trim or body.
Removing and installing a wheel
Change the wheel after loosening the wheel
bolts and raising the vehicle with the jack.
When removing/tting the wheel, the rim may
hit and damage the brake disc. Therefore,
please take care and get a second person to
assist you.
Taking o the wheel
Unscrew the bolts with the wheel wrench
and place them on a clean surface.
Remove the wheel.
Putting on the spare wheel
Check the direction of rotation of the tyre
›››page356.
357


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cupra Formentor 2024 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cupra Formentor 2024 in the language / languages: English as an attachment in your email.

The manual is 17.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cupra Formentor 2024

Cupra Formentor 2024 User Manual - Dutch - 430 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info