Manual Cupra Formentor - 2022 (page 353 of 396) (English)

810366

353

Zoom out

Zoom in

1/396

Wheels and tyres

351

Tyre pressure monitor system

ment panel through a warning lamp and a

warning to the driver ›››Fig.229. When only

one specic tyre is aected, its position within

the vehicle will be indicated.

Loss of pressure: Check left tyre

pressure!

Wheel tread change

The wheel diameter changes when:

●Tyre pressure is changed manually.

●Tyre pressure is insuicient.

●The tyre structure is damaged.

●The vehicle is unbalanced because of a load.

● The wheels on an axle are subject to a heav-

ier load (e.g. with a heavy load).

●The vehicle is tted with snow chains.

●The temporary spare wheel is tted.

●The wheel on one axle is changed.

There may be a delay in the reaction of the tyre

pressure monitoring indicator or it may not

indicate anything under certain circumstances

(e.g. sporty driving, snow-covered or unpaved

roads, or when driving with snow chains).

Calibrate the tyre pressure monitoring indi-

cator

After changing the tyre pressure or replacing

one or more wheels, the tyre pressure moni-

toring indicator must be recalibrated. Do the

same, for example, when the front and rear

wheels are swapped.

It should be calibrated with the vehicle stop-

ped and its tyres cold. If calibrated while the

tyres are hot, the pressure check and calibra-

tion procedure should be repeated when cold

before the next trip.

●Switch the ignition on.

●Memorise the new ination pressure in the

Infotainment system: function button >

Vehicle info > Vehicle status ›››page34.

●OR: through the Service menu on the in-

strument cluster ›››page28.

The tyre pressure loss indicator uses the ABS

sensors to compare the turns of each wheel

and, therefore, their tread circumferences,

among other aspects. After a long journey with

varied speeds the programmed values are col-

lected and monitored.

With the wheels under very heavy loads, the

tyre pressure must be increased to the total

recommended tyre pressure before the cali-

bration ›››Fig.229.

WARNING

When the tyres are inated at dierent pres-

sures or at a pressure that is too low then a

tyre may be damaged resulting in a loss of

control of the vehicle and a serious or fatal

accident.

●If the lamp lights up, reduce speed im-

mediately and avoid any sudden turning or

braking manoeuvres. Stop when possible,

and check the tyre pressure and status.

●The tyre pressure loss indicator only works

correctly if all the tyres are at the correct

pressure when cold, and it is subsequently

calibrated according to the described proce-

dure.

●If a tyre has not been punctured and it does

not have to be changed immediately, drive to

the nearest specialised workshop at a mod-

erate speed and have the tyre checked and

inated to the correct pressure.

Note

●Driving for the rst time with new tyres at

a high speed can cause them to slightly ex-

pand, which could then produce an air pres-

sure warning.

●If excessively low tyre pressure is detected

with the ignition on, an audible warning will

sound. In the event that there is a fault in the

system, an audible warning will sound.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cupra Formentor - 2022 in the language / languages: English as an attachment in your email.

The manual is 7.81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cupra Formentor - 2022

Cupra Formentor - 2022 User Manual - German - 415 pages

Cupra Formentor - 2022 User Manual - Dutch - 424 pages

Cupra Formentor - 2022 User Manual - French - 436 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cupra Formentor - 2022 Manual

Product: