817294
317
Zoom out
Zoom in
Previous page
1/355
Next page
Wheels and tyres
317
Tyre repair
Shake the tyre sealant bottle vigorously
›››Fig.214 10 .
Screw the tyre ination hose ›››Fig.214 3
into the tyre sealant bottle. The bottle's seal
will break automatically.
Remove the ller cap ›››Fig.214 3 and
screw the open end of the tube into the tyre
valve.
With the bottle upside down, empty all of
the contents into the tyre.
Remove the bottle from the valve.
Replace the howitzer with the device
›››Fig.214 1 onto the tyre valve.
Inating the tyre
Screw the tyre ination tube of the compres-
sor ›››Fig.214 8 on the tyre valve.
Check that the air evacuation screw is
closed ›››Fig.214 6 .
Start the engine and leave it running.
Attach the connector ›››Fig.214 9 to the
vehicle’s 12 volt power outlet ›››page201.
Switch on the air compressor with ON/OFF
switch ›››Fig.214 5 .
Keep the air compressor running until it
reaches a pressure of 2.0-2.5 bar (29-36psi/
200-250kPa). A maximum of 8 minutes.
Disconnect the air compressor.
If it does not reach the pressure indicated,
unscrew the tyre inator tube from the valve.
Move the vehicle 10m so that the sealant is
distributed throughout the tyre.
Screw the compressor tyre inator into the
valve.
Repeat the ination process.
If it still does not come up to pressure, the
tyre is too badly damaged. Stop and seek assis-
tance from authorised personnel.
Disconnect the air compressor. Unscrew the
tyre ination tube from the tyre valve.
When the tyre pressure is between 2.5 and
2.0 bars, continue driving without exceeding
80km/h (50 mph).
Attach the sticker ›››Fig.214 2 to the in-
strument panel display, within the driver's eld
of vision.
Check the pressure again after 10minutes
›››page317.
WARNING
When inating the wheel, the air compressor
and the inator tube may become hot.
Protect hands and skin from hot parts.
Do not place the hot exible inator tube
or hot air compressor on ammable material.
Allow them to cool before storing the de-
vice.
If it is not possible to inate the tyre to at
least 2.0bars (29psi / 200kPa), the tyre is
too badly damaged. The sealant is not in a
good condition to seal the tyre. Do not con-
tinue driving. Seek specialist assistance.
NOTICE
Switch o the air compressor after a maxi-
mum of 8 operational minutes to avoid over-
heating! Before switching on the air com-
pressor again, let it cool for several minutes.
Check after 10 minutes of driving
Screw in the inator tube ›››Fig.214 8 again
and check the pressure on the gauge 7.
1.3bar (19psi / 130kPa) and lower:
Stop the vehicle! The tyre cannot be sealed
suiciently with the tyre mobility set.
You should obtain professional assistance
››› .
1.4 bar (20 psi/140 kPa) and higher:
Set the tyre pressure to the correct value
again.
Carefully resume your journey until you
reach the nearest specialised workshop with-
out exceeding 80km/h (50mph).
Have the damaged tyre replaced.
317


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cupra Ateca 2023 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cupra Ateca 2023 in the language / languages: English as an attachment in your email.

The manual is 14.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cupra Ateca 2023

Cupra Ateca 2023 User Manual - German - 387 pages

Cupra Ateca 2023 User Manual - French - 390 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info