534701
30
Zoom out
Zoom in
Previous page
1/31
Next page
Your Print Pad may become un-leveled when transporting your Cube. If this occurs, please follow these instructions to
level your Print Pad for optimum creation experience. The Print Pad pad can be leveled with the two adjusting bolts located
underneath the front and back of the pad.
1. Press the power button on the Cube control panel.
2. Ensure Print Pad is properly installed on print plate.
3. Finger tap SETUP on the touchscreen and scroll through the menu until LEVEL
PLATE appears. Press LEVEL PLATE; the Print Pad will move up to Print Jet tip.
4. Using the Up arrow, raise the Print Pad to the Print Jet tip until the tip is near the
Print Pad but not touching it.
5. Touch the “clockwise” and “counter-clockwise” buttons to automatically move the
Print Jet around the four corners of the Print Pad. During each movement along the
sides of the Print Pad, observe any gaps between the pad and the Print Jet. If there
are gaps on one side of Print Pad and the Print Jet tip is barely touching the Print
Pad on the other side, the Print Pad pad is not level.
NOTE: Please refer to the FRONT TO BACK or SIDE TO SIDE instructions on how
to turn the adjusting knob bolts to level the pad properly.
6. Place a standard sheet of paper between the Print Jet tip and the Print Pad where
the adjustment needs to be made. If the paper cannot slide between the Print Jet tip
and Print Pad, tap the down arrow key on touchscreen.
ROLL SIDE TO SIDE
If the gap between the Print Pad and Print Jet tip is at the right or left side, adjust the pad
using the rear adjusting knob bolt (B). If the gap is too low, the pad is too low and will
need to be moved up.
1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to
loosen and then turn the rear adjusting knob bolt (B) clockwise. To move the pad
down, turn the rear adjusting knob bolt (B) counterclockwise.
2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the
adjustment was needed; the paper should slide back and forth with no resistance. If
resistance is felt, the pad is too high. Please repeat the adjustment.
3. Once adjustments are made, tighten the adjusting knob bolts.
TILT FRONT TO BACK
If the gap between the Print Pad and Print Jet tip is at the front or back of pad, adjust the pad using the rear adjusting knob
bolt (B). If the gap appears on the side, the pad is too low and will need to be moved up.
1. If the pad needs to be moved up, turn the front adjusting knob bolt (A) clockwise to loosen and then turn the back
adjusting knob bolt (B) clockwise. To move the pad down, turn the rear adjusting knob bolt (B) counterclockwise.
2. While adjusting, slide the paper between the Print Jet tip and Print Pad where the adjustment was needed; the paper
should slide back and forth with no resistance. If resistance is felt, the pad is too high. Please repeat the adjustment.
3. Once adjustments are made, tighten the adjusting knob bolts.
NOTE: After the print jet is adjusted, you will need to reset the print jet gap; please refer to Section 16: Setting Print
Jet Gap.
A B
29
24 PRINT PAD LEVELING INSTRUCTIONS
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cubify Cube at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cubify Cube in the language / languages: English as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info