648448
2
Zoom out
Zoom in
Previous page
1/8
Next page
2  •  GB
INTRODUCTION
Congratulations on purchasing your new CTEK professional switch mode battery charger. This charger is part of a range of profes-
sional battery chargers from CTEK SWEDEN AB. It represents the latest technology in battery charging with charging and analysis 
in eight steps with temperature compensation. Read this User Manual and follow the instructions carefully before using your
new charger.
SAFETY
The charger is designed for lead-acid batteries. Do not use the charger for any other purpose
Use safety glasses and turn your head away when connecting or disconnecting a battery.
Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin or eyes. Seek medical advice.
Make sure that the cable is not pinched or in contact with warm surfaces or sharp edges.
While charging, a battery can emit explosive gases, so it is important to avoid sparks in the immediate area.
Always provide for proper ventilation during charging.
Avoid covering the charger. 
Make sure that the electrical cable does not come into contact with water. 
Never charge a frozen battery.
Never charge a damaged battery.
Do not place the charger on the battery while charging.
The electrical connection must full the national heavy current requirements.
Check the charger cabling before use. Make sure there are no cracks in the cabling or in the protective covering. A charger with 
damaged cables may not be used.
Always check that the charger has gone over to maintenance charging mode before leaving the charger unattended and 
connected for long periods. If the charger had not gone over to maintenance charging within 3 days, this is an indication of a 
problem. In this case the charger must be disconnected manually.
All batteries fail sooner or later. A battery that fails during charging is normally taken care of by the chargers advanced control, 
but certain uncommon errors in the battery can still arise. Don’t leave the battery charger unattended for a longer period of time.
Only mount the charger on a at surface.
This equipment may not be used by children or by those who can not read and understand the manual if they are not supervised
by a responsible person who can guarantee that the battery charger is being used in a safe manner. Store and use the battery 
charger out of the reach of children. Make sure that children do not play with the battery charger. 
When using outdoors the charger has to be positioned horizontally with the long side or top side turned up. 
CHARGING
Connecting the charger to a battery tted in a vehicle
1. The power cord should be disconnected when connecting or disconnecting the battery leads.
2. Identify the battery terminal that is grounded (connected to the chassis). The negative terminal is normally the grounded post.
3. Charging a negatively grounded battery. Connect the red cable to the positive terminal on the battery and the black cable to 
good metal engine ground away from the battery. Ensure you do not connect the black cable to fuel lines or sheet-metal body 
parts. 
4. Charging a positively grounded battery. Connect the black cable to the negative terminal on the battery and the red cable to 
good metal engine ground away from the battery. Ensure you do not connect the red cable to fuel lines or sheet-metal body parts. 
Connecting the charger to an out of vehicle battery:
1. The power cord should be disconnected when connecting or disconnecting the battery leads.
2. Connect the red cable to the positive terminal on the battery and the black cable to the negative terminal. 
If the battery leads have been connected incorrectly, the reverse polarity protection system will ensure that neither the charger nor 
the battery are damaged. 
Start charging
1. Connect the chargers AC cord to an AC Power Supply. The charger will indicate POWER, yellow indication lamp (B).
2. The lamp for completely discharged battery (1) will illuminate if the battery’s voltage is less than 12V for MULTI XS 25000 and 
XS 25000 or 24V for MULTI XT 14000 or XT 14000. 
3. Normal charging will be indicated by the following lights: completely discharged battery (1), bulk charging (2), absorption 
charging (3) or maintenance charging (4). When the maintenance charging lamp illuminates the battery is fully charged. Charging 
will start if the voltage drops. The charger can normally be connected for months. Reconditioning (only on MULTI XS 25000 and 
MULTI XT 14000) is indicated by the lamp (5) illuminating. 
4. If the battery leads have been connected incorrectly, the reverse polarity protection system will ensure that neither the charger 
nor the battery are damaged. 
5. If nothing happens. If the lamp indicating the setting and the power lamp remain lit but no other lamp illuminates, the connection 
to the battery or chassis may be poor or the battery may be faulty. Another cause may be a lack of voltage in the AC Power Supply. 
Begin by improving the connection between the battery and charger.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ctek XS 25000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ctek XS 25000 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ctek XS 25000

Ctek XS 25000 User Manual - German - 9 pages

Ctek XS 25000 User Manual - Dutch - 8 pages

Ctek XS 25000 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info