648523
14
Zoom out
Zoom in
Previous page
1/26
Next page
66 • FR
INSTALLATION DE L’UNITÉ
1. Fixez le support de la sonde de température sur une surface
plane d’une batterie de service. Placez-le aussi près que
possible d’une borne positive.
2. Utilisez le gabarit de perçage joint. Le câblage est simplifié
si les unités sont installées selon le gabarit de perçage mais
d’autres configurations sont possibles.
3. Montez le ou les appareils sur une surface où ils peuvent
être correctement fixés et où ils ne sont pas exposés aux
carburants, aux huiles ou aux projections de saleté.
4. Montez l’appareil avec des vis prévues pour la surface et
fixez-le avec une vis dans chaque trou de ses quatre coins.
Voir l’image 1. Montez l’unité avec des vis M4 ou ST4.2.
Le couple nécessaire dépend de la surface de montage. La
figure 1 représente un CTEK D250S. La même procédure
sapplique à tous les appareils.
5. Attachez les câbles et vissez leurs vis au couple de
7 Nm/62 Lb-In. Utilisez des outils, la force manuelle sans
outil nest pas suffisante.
6. Consulter le tableau ci-dessous.Le câble de masse du
SMARTPASS doit être connecté à la vis de masse du
DUAL ou à n’importe quel point de connexion de masse
accessible.
INSTALACIÓN DE
LOS CABLES
Figure 1
Figure 2
2Nm/18 Lb-In
7Nm/62 Lb-InClé Allen
AVERTISSEMENT
!
Les D250S DUAL et SMARTPASS
ne sont pas protégés contre
l’inversion de polarité.
Déconnectez des bornes de la
batterie avant le montage.
AVERTISSEMENT
!
Le D250S Dual n’est pas anti-
étincelles. Prévoyez une bonne
ventilation.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ctek SMARTPASS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ctek SMARTPASS in the language / languages: French as an attachment in your email.

The manual is 3,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ctek SMARTPASS

Ctek SMARTPASS User Manual - English - 24 pages

Ctek SMARTPASS User Manual - German - 12 pages

Ctek SMARTPASS User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info