498273
17
Zoom out
Zoom in
Previous page
1/20
Next page
17
Connect RCA Cables
from head unit with RCA
inputs (LINE INPUT
1CH/2CH & 3CH/4CH)
Connection for
Remote to adjust
the subwoofer from
your seat
5-Channel Amplifier - Speaker wiring and Connection
MXB 5900i
X-Over- (Front-/Rearsystem 1 up to 4 Channel)
• When you use bigger speaker systems (Ø20cm plus),set on FULL RANGE-position (FULL RANGE).
• When you use smaller speaker systems (Ø8.7cm - Ø16cm), set on HIGHPASS- position (HIPASS). The cut-off frequency should be
between 60Hz - 150Hz. It is controlled by the HIPASS-regulator. When you use this configuration the LOPASS CONFIG - Switch is out of
function.
Subwoofer (Channel 5)
•The cut-off frequency should be between 60Hz - 100Hz. It is controlled by the Lowpass-regulator
Bass EQ-(Channel 5)
Allows you to adjust the bass boost from 0dB up to 12dB
Caution! Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.
Level
• Turn the INPUT LEVEL control on the amplifier to 5V position.
• Turn the head unit volume control to about 80-90% of its full setting.
• Turn the INPUT LEVEL control clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL control slightly until you can hear clean sound.
Mode
• If there is only one RCA output at your head unit, set mode-switch on 2CH-postion.
5CH-Stellung bringen.
Interconect cable checklist :
• Connect the RCA outputs from head unit with the RCA Inputs (LINE INPUT 1CH&2CH / 3CH&4CH) of
the 4 Channel amplifier with two RCA Cables.
• Connect the RCA outputs of the (LINE OUT) 4-Channel Amplifier with the RCA inputs(LINE INPUT) of
the 1-Channel/Mono amplifier with an RCA cable.
• Connect the Front- & Rear-Speakers with a good RCA cable with the speaker outputs (SPEAKER
OUTPUT/ + 1CH -, + 2CH -, + 3CH -, + 4CH -) of the 4-Channel amplifier.
• Connect the Subwoofer with a good RCA Cable with the Speaker outputs (SPEAKER / + -) of the 1-
Channel/Mono Amplifier.
• The minimum final speaker impedance must not be below 2 Ohm per channel. Too low speaker loads
result in too high heat dissipation and may cause the amplifier run into protection.
• Please observe speaker channel and polarity as printed by the speaker terminal
Caution!
Be careful not to connect speaker (-) to the ground or vehicle chassis.
Subwoofer
2 - 8 Ohm
Front-Speakers
4 - 8 Ohm
0 dB 18 dB
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch MXB 5900i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch MXB 5900i in the language / languages: English, German as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info