63458
24
Zoom out
Zoom in
Previous page
1/28
Next page
Speaker- and Audio-Connections: MXB480 / MXB4125
3-Channel Stereo-/Subwoofer-Mode
Connect the RCA INPUTS of the amplifier to the head unit line outputs with appropriate
RCA cables. If your head unit is not equipped with pre-amplifier RCA line outputs you
can use the optional HI INPUTS (Highlevel Inputs). Connect therefore the speaker outputs of your
head unit with the enclosed cable plug. Check the Wiring Diagram below.
Connect the frontspeakers with the speaker ouputs (SPEAKERS/ + CH1 -, + CH2 -) and the subwoofer
with the speaker outputs (+ BRIDGED - from CH3/4) of the amplifier by using appropriate cables.
Ensure that the total speaker impedance load is not lower than 2 Ohms channel on channel 1/2 and
4 Ohms on subwoofer channel 3/4.
Too low speaker loads result in too high heat development and may cause the amplifier run into
protection.
INPUT SELECT - switch
• Select here the 4CH-Position.
FILTER - selector channel 1/2
If larger speakers (> Ø20 cm) are used, the FLAT position is recommended. A fullrange signal will be provided to the speakers.
For all smaller speakers (Ø8.7cm - Ø16cm) the Position HIGH PASS is recommended, thereby the lower frequencies will eliminated
in the audiosignal. Set the cut-off frequency between 60Hz - 150Hz, depending of the size of the installed speakers.
The cut-off frequency is adjustable with the HIGH PASS controller.
• In this configuration example the LOW PASS - controller is not used.
INPUT LEVEL - controller channel 1/2
• Turn the INPUT LEVEL controller on the amplifier to 4V position.
• Turn the head unit volume controller to about 80-90% of its full setting.
• Turn the INPUT LEVEL controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controller slightly until you can hear clean sound.
REFERENCE NOTE: If this controller is cranked up too high, the amplifier produce distortions, which may cause a
“creeping death” of the amplifier (or the speakers). Usually this is called “Clipping”.
BASS BOOST - controller channel 1/2
• Turn the BASS BOOST controller into “0dB” - position.
FILTER - selector subwoofer channel 3/4
In the Subwoofer-Mode mono bridged the FILTER - select must be in position LOW PASS, thereby the higher frequencies will be
eliminated in the audiosignal. Set the cut-off frequency between 60Hz - 100Hz, depending on the size of the installed subwoofer
The cut-off frequency is adjustable with the LOW PASS - controller. In this configuration the HIGH PASS - controller is not used.
INPUT LEVEL - controller subwoofer channel 3/4
• Turn the INPUT LEVEL - controller on the amplifier to 5V position.
• Turn the head unit volume controller to about 80-90% of its full setting.
• Turn the INPUT LEVEL - controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL - controller slightly until you can hear clean sound.
REFERENCE NOTE: If this controller is cranked up too high, the amplifier produce distortions, which may cause a
“creeping death” of the amplifier (or the speakers). Usually this is called “Clipping”.
BASS BOOST - controller subwoofer channel 3/4
• The BASS BOOST - controller adjusts the bass boost from 0db to +12dB.Caution! Please use the Bass Boost carefully.
REFERENCE NOTE: Ensure always correct polarity for all connections.
Don’t connect any speaker cables to the vehicle’s ground.
24
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch MXB 480 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch MXB 480 in the language / languages: English, German as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info