168679
24
Zoom out
Zoom in
Previous page
1/32
Next page
GTX4400
24
FUNCTIONS AND OPERATIONAL CONTROLS
1
2
POWER/PROTECT (This LEDs are located on the opposite panel next to the fuse)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
3
4
The BASS BOOST CH1/2 and CH3/4 controllers adjust the bass boost enhancement continuously from 0dB to +12dB at
45 Hz for the regarding channel pair (Channel 1/2 or Channel 3/4).
5
The CH1/2 and CH3/4 X-OVER switch selects the required operation mode of the amplifier on the regarding channel pair
(Channel 1/2 or Channel 3/4).
Position LP: Lowpass mode (The higher frequencies will be eliminated. Adjustable by the lowpass controller.)
Position HP: Highpass mode (The higher frequencies will be eliminated. Adjustable by the highpass controller.)
Position FULL: Fullrange mode (The whole frequencies will be amplified).
6
The LOW PASS CH1/2 and CH3/4 controllers adjust the cut-off point of the frequency range to above for the regarding
channel pair (Channel 1/2 or Channel 3/4). The cut-off frequency is continuously adjustable from 30 Hz to 250 Hz.
7
The INPUT MODE switch must be in 2CH position, if you connect only one RCA stereo audio cable with the CH1/2 line inputs.
Select the position 4CH, if you connect two RCA stereo audio cables with CH1/2 and CH3/4 line inputs.
The fader function of your headunit works only in the 4CH mode.
If you have select the 2CH mode, the input signal of LINE INPUT CH1/2 will be routed to the channelpair CH3/4. Due to this, only
one RCA stereo audio cable is required. Therefor the additional available subwoofer lineout (SUB OUT) of your headunit is
recommended in the LP mode and no Y-Adaptors are required.
Choose the 3CH mode only if you run a subwoofer in bridge mode on Channel 3 and 4. Thereby the signal on Channel 3 and 4
will be summed to a mono signal.
8
9
The HIGH PASS CH1/2 and CH3/4 controllers adjust the cut-off point of the frequency range to below for the regarding channel
pair (Channel 1/2 or Channel 3/4). The cut-off frequency is continuously adjustable from 60 Hz to 1200 Hz (1.2 kHz).
The LEVEL INPUT CH1/2 and CH3/4 controllers adjust the input sensitivity of the amplifier to align the audio signal of the head
unit for the regarding channel pair (Channel 1/2 or Channel 3/4). The input sensitivity is adjustable from 4 to 0.2 Volts.
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
By connecting only the CH1/2 jacks, the INPUT MODE switch must be set to the 2CH position.
The LINE OUT RCA jacks provide a linear fullrange audiosignal to supply an additional amplifier.
The High Level Inputs are suitable to connect the amplifier inputs with speaker wires, if your headunit is not equipped with pre-
amplifier RCA outputs. Never use the High Level Inputs and the RCA inputs at the same time. This may damage the amplifier
seriously. Attend therefor the descriptions on page 28.
1 2 3 4 5 6 7 98
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch gtx 2200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch gtx 2200 in the language / languages: English, German as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info