498267

Crunch GTi 1500 Manual

11
Zoom out
Zoom in
Previous page
1/32
Next page
11
ENG
POWER SUPPLY AND TURN ON CONNECTION (FIG. 2)
(1) GND terminal for the ground
(2) REMOTE terminal for the turn on connection
(3) +12 V terminal for the positive-connection of the battery
(4) Vehicle’s battery
(5) In-Line Fuse (not included in the scope of delivery)
(6) Turn on wire from the headunit or the electrical antenna
(7) Fuses
FIGURES (P. 28-30)
The POWER-LED (fig. 1,1) lits up, if the amplifier is in operation.
The PROTECT-LED (fig. 1, 1) lits up, when the amplifier is overheated, or a short circuit occurs resp.
a too low impedance load is connected to the speaker outputs. If this events, the internal built-in
protection circuit shuts down the amplifier automatically. The amplifier should work again properly after
you have solved the problems.
PROTECTION CIRCUIT
CONNECTIONS AND CONTROLLERS (FIG. 1)
(1) Power-LED / Protect-LED
(2) Connector for the included bass level remote controller
(3) Bass Boost controller
(4) Lowpass filter controller
(5) Selector LP (Lowpass) / FULL / HP (Highpass)
(6) Subsonic / highpass filter controller
(7) Gain level controller
(8) Audio signal outputs to run additional amplifiers
(9) Audio signal inputs
1-CHANNEL OPERATION MONO (FIG. 3)
If you want to run the amplifier with the 2 line output channels from the headunit to drive one or two
subwoofers, connect the following setup:
(1) To the headunit, line output rear left or subwoofer output
(2) To the headunit, line output rear right or subwoofer output
(3) Bass level remote controller
(4) Operation with 1 subwoofer
(5) Operation with 2 subwoofers
2-CHANNEL OPERATION STEREO (FIG. 4)
If you want to run the amplifier with another amplifier (same model) to drive 2 loudspeakers in stereo,
connect the following setup:
(1) Amplifier 1 via Y-Connector*, to the headunit, line output left
(2) Amplifier 2 via Y-Connector*, to the headunit, line output right
(3) Loudspeaker left
(4) Loudspeaker right
* both jacks under INPUT L/R must be connected.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch GTi 1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch GTi 1500 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info