498245
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
Interconnect cable checklist:
•Connect the INPUT of the Stereo (Front) Amplifier to the head unit line outputs with good
quality RCA to RCA cables.
• Connect the OUTPUT of the Stereo (Front) Amplifier with the INPUT of the designated Bass
(Rear) Amplifier with a further RCA cable.
• Connect the speakers with the terminal block (SPEAKER OUTPUT/ + RIGHT - and + LEFT
-) of the Stereo (Front) Amplifier.
• Connect the Subwoofer with the terminal block (SPEAKER OUTPUT/ + BRIDGED - ) of the
designated Bass (Rear) Amplifier.
•The minimum final speaker impedance must not be below 2 Ohms for the Stereo Amplifier,
the total impedance of the Subwoofer(s) must not be below 4 Ohms. Too low speaker loads
result in too high heat dissipation and may cause the amplifier run into protection.
• If you use more than one speaker (Subwoofer), make sure that both are connected in
phase. Incorrect polarity of the speakers results in total loss of bass response.
Control settings of the Stereo (Front) Amplifier:
X-OVER SELECT
If larger than 20 cm speakers are used, the FULL position is recommended.
For all smaller speakers (Ø8.7cm - Ø16cm) the Highpass-Position (HP) is recommended, which eliminates the lowest
frequencies and protects the speakers from damage. Set the crossover-frequency between 60Hz - 150Hz, depending of the
size of the installed speakers. The Highpass adjustment can be done with the FREQ - ADJUST control.
INPUT LEVEL
• Turn the INPUT LEVEL control on the amplifier to 5V position.
• Turn the head unit volume control to about 80-90% of its full setting.
• Turn the INPUT LEVEL control clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL control slightly until you can hear clean sound.
BASS BOOST
• Turn the BASS BOOST control into “0dB” - position.
MODE SELECT
• The MODE SELECT - switch must be in “STEREO” - position.
Control settings of the Bass (Rear) Amplifier:
X-OVER SELECT
In 1 Channel/Mono-Mode select the Lowpass-Position (LP), which eliminates the higher frequencies. The recommended
crossover frequency ranges between 60 - 100Hz, depending on the size and response of the Subwoofer. The Lowpass
adjustment can be done with the FREQ - ADJUST control.
INPUT LEVEL
see descriptions for Stereo Amplifier above
BASS BOOST
• The BASS BOOST - Control increases the bass level at 45 Hz max. +12dB.
Caution! Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.
MODE SELECT
• The MODE SELECT - switch must be in “MONO” - position.
2 Channel Amplifer - Applications
GP1000.2 / GP1500.2
One 2 Channel Amplifier in Stereo Mode (Front Amplifier) with
One 2 Channel Amplifier in Mono/Subwoofer Mode (Rear Amplifier)
Caution
Be careful not to connect speaker (-) to the ground or vehicle chassis.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch GP1500.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch GP1500.2 in the language / languages: English, German as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info