169008
26
Zoom out
Zoom in
Previous page
1/32
Next page
DSX4500
26
INTERCONNECTION EXAMPLE 2-Channel Mode: 2 x Mono Subwoofer bridged
INTERCONNECTION
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT. All LINE INPUT jacks must be connected (CH1/CH2/CH3/CH4).
Therefor you need to use two Y-connectors to splice the audio signal. If a separate SUB OUT from your headunit is available, use this
as LINE OUT.
Connect the subwoofers with the SPEAKER OUTPUTS CH1/2 + BRIDGED - and CH3/4 + BRIDGED -.
Ensure by any means, that the total impedance load of all subwoofers per channelpair is not lower than 4 ohms. Too low impedance
cause high temperature and will shut down the amplifier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
In the mono/subwoofer mode the X-OVER switch must set to the LP/BP position (Lowpass/Bandpass mode), thereby the higher
frequencies will be eliminated. The cut-off frequency ist adjustable with the LOW PASS controller and should be set between
60 to 100 Hz, depending on the size of the subwoofer.
In the lowpass mode (LP/BP) the HIGH PASS controller works also as subsonicfilter, that eliminates the ultra-low, not hearable and
harmful frequencies to generate a bandpass signal (Bandpass mode). The subsonic frequency should be set between 15 to 40 Hz,
depending on the size of the subwoofer. NOTE: If this value is higher than the lowpass setting, no sound is hearable.
LEVEL CONTROLLER CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
• Turn the INPUT LEVEL controller of the amplifier to the 6V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the INPUT LEVEL controller clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER CH1/2 & CH3/4 (SUBWOOFER 1 & SUBWOOFER 2)
• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of
the amplifier by using two Y-connectors
Subwoofer 1
4 – 8 Ohms
LINE INPUT OUTPUT
R
L
CH1/CH2
CH3/CH4
LOW PASS
BASS BOOST
INPUT LEVELHIGH PASS
X-OVER
LP/BP FULL
HP
LOW PASS
BASS BOOST
INPUT LEVELHIGH PASS
X-OVER
LP/BP FULL
HP
CH1 CH3
CH2 CH4
30Hz
150Hz
0dB 12dB
6V
0.2V
10Hz
150Hz
30Hz
150Hz
0dB 12dB
6V
0.2V
10Hz
150Hz
POWER INPUT
GND REM
SPEAKER OUTPUT
CH1 CH2 CH3 CH4
BRIDGED BRIDGED
FUSE
12V
L R
Switch position LP/BP
Switch position
LP/BP
Y-Connectors
Subwoofer 2
4 – 8 Ohms
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crunch dsx2350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crunch dsx2350 in the language / languages: English, German as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info