581449
11
Zoom out
Zoom in
Previous page
1/52
Next page
XTi2 Series Power Amplifiers
page 11
Operation Manual
Integrated Processing Features
The XTi2 Series amplifiers include a number of integrated processing features which appear as icons on the front panel LCD
screen. They are described below:
NOTE: System Architect Software is required to have full control over all Integrated Processing Features which can be
downloaded from the following URL – http://hiqnet.harmanpro.com/. When controlling more than one XTi2 at a time
you will need USB Hub. We recommend using a Powered USB Hub.
Input Mode
t 4UFSFP*OUIJTNPEF$IBOOFMJOQVUHPFTUP$IBOOFMPVUQVUBOE$IBOOFMJOQVUHPFTUP$IBOOFMPVUQVU5IJTJT
the mode the amplifier is configured for from the factory.
t 46.$)$)o*OUIJTNPEFUIF$IBOOFMJOQVUTJHOBMBOE$IBOOFMJOQVUTJHOBMBSFTVNNFEBOEGFEUPCPUI
output channels. This provides a 6 dB level boost.
t *OQVU:o*OUIJTNPEFUIF$IBOOFMJOQVUTJHOBMJTTFOUUPUIF$IBOOFMBOE$IBOOFMPVUQVU5IFDIBOOFMJOQVU
signal is ignored.
Output Mode
t 4UFSFPo*OUIJTNPEFUIFBNQMJmFSTFOET$IBOOFMJOQVUTJHOBMUPUIF$IBOOFMPVUQVUBOEUIF$IBOOFMJOQVUTJHOBM
to the Channel 2 output.
t #SJEHF.POPo*OUIJTNPEFUIFQPXFSPGCPUIBNQMJmFSDIBOOFMTBSFEFMJWFSFEJOUPBTJOHMFPSPINMPBE
Subharmonic Synth
The Subharmonic Synth feature takes the low frequencies and “synthesizes” or creates new frequencies that are one octave
lower. The two signals are then summed together. Also new, are two user adjustable parametric EQ filters and crossover
frequency filter. These can be used to “shape” the sound and enhance the desired effect.
Equalization
The XTi2 Series provides two blocks of equalization in the signal processing. The input EQ block is before the crossover and
is usually used for the room EQ. The output EQ block is after the crossover and is usually used for speaking tuning.
Input EQ: This input EQ block provides 6 filters per channel each with frequency, gain, and Q that is user controllable.
This block also has a High and Low Shelf Filter per channel which has gain and frequency control.
Output EQ: This output EQ block provides 8 filters per channel each with frequency, gain, and Q control that is user
controllable.
Crossover:
The crossover section provides users with the ability to enable a HighPass and LowPass filter per channel along with
BandPass gain and the ability to change the polarity. This allows the Crossover section to be customized to most system
configurations.
For the HighPass and LowPass Filters, you have the choice of the following filters: Butterworth 6dB/oct, Butterworth 12dB/oct,
Butterworth 18dB/oct, Butterworth 24dB/oct, Butterworth 48dB/oct, Linkwitz-Riley 24dB/oct, and Linkwitz-Riley 48dB/oct.
The BandPass gain provides you with -15dB to +15dB of gain.
Delay
There is up to 50msec of delay available in the signal processing for time aligning your speakers. The software allows you to
enter the amount of delay needed in the form of seconds, feet, or meters and does the calculation for you.
Peak
X
Plus Limiter:
Feed-forward output limiter with user-adjustable attack, release and threshold (0.1 dB resolution), plus integrated feedback
limiter to minimize amplifier clipping.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crown XTi 4002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crown XTi 4002 in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info