772389
19
Zoom out
Zoom in
Previous page
1/52
Next page
17
CroozerKidPlus-Kid19-ENG-1-19
Converting the Croozer to a Bicycle Trailer
Installing the axle hitch to the towing bicycle
The hitch assembly is always mounted to the left side of
the bicycle (relative to the direction of travel) and consists
of two parts: a hitch connector (1), which is attached to the
hitch arm, and an axle hitch (2), which must be mounted to
the rear axle of the towing bicycle.
Before installing the axle hitch, you must rst check
whether the bicycle is suitable for towing a trailer. This
information can be obtained from the bicycle manufacturer,
a bicycle shop or the owner’s manual of the bicycle.
It is vitally important to confirm that the towing bicycle is
suitable for pulling trailers. Pulling a trailer with a bicycle
that has not been approved by its manufacturer for use
as a towing bicycle can result in frame breakage or other
material damage. Breakages of this kind could cause ac-
cidents with serious injury or death.
If you are not completely condent about your ability to in-
stall the axle hitch correctly, please consult with, or have the
installation performed by, a professional bicycle mechanic.
It is vitally important that the axle hitch be properly installed.
An improperly installed axle hitch could come loose while
riding and cause accidents with serious injury or death.
Installing the axle hitch to a bicycle with a quick-
release axle
Tip: If the bicycle wheel is equipped with a thru axle (with
quick release lever) instead of a conventional quick-
release skewer, the thru axle must be replaced with
the Croozer Thru Axle available as an accessory.
Other hitch axles are also available as accessories.
The quick-release lever must be positioned on the right
side of the bicycle (relative to the direction of travel). If the
lever is on the left side, the quick-release skewer must be
removed and reinserted from the right side. Be sure to fol-
low the applicable instructions in the owner’s manual of the
bicycle and/or consult a professional bicycle mechanic.
1. Open the quick-release lever (1) on the rear wheel
of the towing bicycle or loosen the Allen bolt (5 mm),
depending on the type of quick-release skewer. Often,
the open position is indicated on the lever by the word
“OPEN”. In this case, when the word “OPEN” can be
seen, the lever is in the open position.
2. Remove the axle nut (2) of the quick-release skewer
by turning the nut anticlockwise. Use caution: the
spring located just beneath the nut is under tension
and could y off when removing the nut.
3. Fit the axle hitch (3) over the end of the quick-release
skewer without removing the spring.
4. Thread the axle nut (2) back onto the skewer. Tighten
the axle nut at least ve full turns (clockwise).
The axle nut must engage the threads for at least five
full turns in order to ensure adequate clamping force for
holding the rear wheel securely. Failure to tighten the
axle nut adequately may result in accidents with serious
injury or death. If it is not possible to tighten the axle nut
five full turns, then the quick-release skewer is too short
and must be replaced. Consult a professional bicycle
mechanic for the appropriate parts and assistance.
2
1
1
2
3
2
3
min. 5 x
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Croozer Kid Plus 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Croozer Kid Plus 2019 in the language / languages: English as an attachment in your email.

The manual is 9.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Croozer Kid Plus 2019

Croozer Kid Plus 2019 User Manual - German - 52 pages

Croozer Kid Plus 2019 User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info