735869

Crivit SB6044 IAN 311060 Manual

16
Zoom out
Zoom in
Previous page
1/50
Next page
18 GB/IE
• Do not over-inflate because you then risk tear-
ing open the welded seams. Close the valves
properly after inflating.
• Avoid contact with sharp, hot ,pointed, or
dangerous objects.
Assembly
Follow the individual assembly steps
in the order indicated. If the correct
sequence for inflating the three air
chambers is not followed the pressure
may be distributed unevenly.
This can lead to instability of the dinghy
and adversely affect its handling char-
acteristics.
• Assembly should always be performed by two
adults because of the product’s size.
• Select a smooth and clean surface with
enough space to unfold the dinghy. Check
that all the individual parts are there and in
good order and condition.
• After assembling for the second time the
dinghy should be inspected for any possible
damage, holes, and tears and these should be
sealed as described in the section “Repairs”.
Once you are on the water it is no longer
possible to remedy any damage.
• Do not over-inflate the air chambers in order
not to overstretch the foil.
• Make sure that the inflated dinghy does not
come into contact with stones or other sharp
objects and become damaged.
Assembly the screw-on valves
(fig. B)
The chambers and of the dinghy are
each provided with a threaded opening for the
enclosed screw-on valves (4) provided.
1. Pull the loop (4a) of the valve over the thread-
ed opening (1a) so that it lies firmly in the
groove provided for that purpose.
2. Turn the base (4b) clockwise into the threaded
opening.
Inflation
WARNING!
• Follow the correct sequence when inflating the
air chambers.
• The recommended operating pressure is
0.04bar ( = 40mbar = 0.58psi).
• Avoid inflating the air chambers too much
because there is the risk of over-stretching the
welded seams or even tearing them open.
• To inflate the product use standard commer-
cial foot pumps or double-stroke piston pumps
with matching adapter attachments, and
where applicable a pressure gauge.
• To inflate the product do not use a compressor
or compressed air bottle.
This can lead to damage to the product.
• Always inflate all air chambers fully.
Inflation sequence
Inflate the air chambers in the following se-
quence:
1. - Safety chamber with screw-on valve
2. - Bottom chamber with plug valve
3. - Flotation chamber with screw-on valve
Note: The air chambers are marked with the
corresponding numbers on the dinghy.
( - ) (fig. F).
Filling the air chambers
IMPORTANT!
The PVC material expands somewhat
after the product is inflated for the first
time and does not return to its original
condition. Remember that the specifi-
cations may vary slightly depending on
the load and outside temperature.
• To inflate the product use standard commer-
cial foot pumps or double-stroke piston pumps
with matching adapter attachments, and
where applicable a pressure gauge.
1. Safety chamber with screw-on valve
1. Open by turning the seal cap (4c) of the
screw-on valve (4) anticlockwise (fig. B).
2. Inflate the safety chamber
until the length
of the imprinted measuring strip matches that
of the control ruler (fig. G).
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit SB6044 IAN 311060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit SB6044 IAN 311060 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info