Manual Crivit RG 4791 IAN304119 (page 27 of 86) (English, German, Dutch, French, Polish)

736216

Zoom out

Zoom in

1/86

CAUTION: Check the plus/minus poles

of the batteries (30) and that they are in-

serted correctly, as marked on the bottom

of the battery compartment (10d).

3. Attach the battery compartment cover (10c) on

the back of the cockpit and tighten the screws

back in again.

Replacing the batteries

CAUTION: Observe the following

instructions to avoid mechanical

and electrical damage.

Should the batteries (30) no longer function,

replace them as described in the insertion instruc-

tions above. Remove the batteries that are in the

device before inserting new ones.

Notes on setting up

• Choose an exercise area of approx.

3.00 x 1.80m (L x W).

• Train on a ﬂat and non-slip surface only.

Assembly

The item should be assembled by two

people.

Step 1 (Fig. C):

1. Attach the two front legs (7a), (7b) to the front

foot (3).

Note: Make sure that the curved part on the two

legs (7a), (7b) are each face outwards.

2. Then attach the two long legs (7a), (7b) to the

base frame (1).

Note: To make it easier to assemble the legs, turn

the base frame so that the bolt holes are facing

upwards.

Step 2 (Fig. D):

1. Leave the base frame (1) in the inverted state

and mount the centre leg (9).

Note: After completing the assembly of the

rowing machine, the floor height level can be

adjusted with the thumbscrew.

2. Adjust the ground levelling with the thumbscrew

and then tighten the lock nut (9a).

Step 3 (Fig. E):

1. Leave the base frame (1) in the inverted state

and mount the two footrests (6a), (6b).

Note: Make sure they are correctly oriented (left

(6a)/right (6b)).

Step 4 (Fig. F):

1. Attach the two rear legs (8a), (8b) to the rear

foot (4).

Note: Make sure that the curved part on the two

legs (8a), (8b) are each face outwards.

2. Slide the metal plate (15) into the slide rail (2)

and attach the rear legs (8a), (8b) to the slide

rail (2).

Note: Make sure that the threaded holes on the

metal plate (15) are directly under the holes on

the slide rail (2).

Step 5 (Fig. G):

1. Slide the saddle (5) from behind onto the slide

rail (2). To do this, direct the gliding carriage

under the seat into the guide on the slide rail.

Note: Make sure the seat is correctly oriented.

2. Attach the stoppers (13) to the right and left on

the front and back end of the slide rail (2).

3. Insert the cover panel (14) onto the back end

of the slide rail (2).

Step 6 (Fig. H):

1. Place the base frame (1) and the slide rail (2)

on the respective feet.

2. Insert the slide rail (2) in the base frame (1)

and screw it tight. Make sure the two sensor

cables are not crushed or damaged when

inserting the slide rail (2).

3. Fold the slide rail up (2) and insert the connec-

tor of the sensor cable (1a) into the corre-

sponding bushing (2a) of the slide rail.

Step 7 (Fig. I):

When in the unfolded state, the slide rail (2) must

be stabilised with the safety bolt (11).

1. Put the bushing (12) on the safety bolt (11).

2. Screw the safety bolt (11) from below into the

threaded hole provided on the slide rail (2).

Note: Tighten the locking screw (11) so that

the rowing machine has a stable footing during

training.

Step 8 (Fig. K):

1. Connect the two sensor cables of the cockpit

(10a) with the sensor cables of the base frame

(1b).

2. Screw the cockpit holder (10b) firmly to the

base frame (1).

GB/IE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit RG 4791 IAN304119 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit RG 4791 IAN304119 Manual

Product: