735864

Crivit Inshore 335 VII IAN 311071 Manual

18
Zoom out
Zoom in
Previous page
1/54
Next page
20
Securing the front seat (fig. D)
1. Inflate all air chambers of the front seat (3)
until they feel firm and push down the valves.
2. Place the seat between the two upper side
chambers , to ensure that the it stays
firmly in place.
Note: The hook-and-loop straps on the backrest
of the front seat (3) must point towards the stern
(1f).
3. Secure the seat with the 80cm cord (9b) at
the grommets (1a) on the floor chamber
(fig. D) using a reef knot (fig. C).
4. Attach the backrest of the seat (3) at the
buttons (1b) on the two lower side chambers
, using the elastic bands attached to the
kayak so that it forms a zigzag pattern (fig. E).
Attaching the bowsprit guard
1. Inflate the air chamber of the bowsprit guard
(2).
2. Push the safety buttons of the bowsprit guard
into the openings on the kayak (fig. O). Make
sure that they seat firmly.
3. Attach the bowsprit guard (2) at the buttons
(1b) on the two upper side chambers ,
using the pre-installed elastic band so that it
forms a zigzag pattern (fig. F).
Attaching the stern splash guard
with seat
1. Inflate all air chambers of the stern splash
guard (4).
2. Press the seat down under the two upper side
chambers , to ensure that it stays firmly
in place.
3. Push the safety buttons of the stern splash
guard into the openings on the kayak (fig. O).
Make sure that they seat firmly.
4. Attach the stern splash guard (4) at the but-
tons (1b) on the two upper side chambers ,
using the pre-installed elastic band so that
it forms a zigzag patter. (fig. G).
Triangular cushion
1. Inflate the triangular cushion (5) and press
down the valve.
2. Position the inflated triangular cushion (5)
firmly in the bow of the kayak.
Note: The triangular cushion (5) serves as a
footrest for the person sitting at the front.
4. Close the valve seal and push in the valve by
pressing lightly (fig. J/K).
3. Upper side chambers with screw-on
valve
1. Open by turning the seal cap (10c) of the
screw-on valve (10) anticlockwise (fig. H).
2. Inflate the upper side chambers
, using
the appropriate pump.
3. Check the operating pressure as described in
the section “Checking the operating pressure”.
4. Turn the seal cap (10c) of the screw-on valve
(10) clockwise to close it again.
Checking the operating pressure
IMPORTANT!
The PVC material expands somewhat
after the product is inflated for the first
time and does not return to its original
condition. Remember that the specifica-
tions may vary slightly depending on
the load and outside temperature.
1. Inflate the floor chamber and the two
lower side chambers , until they feel
firm and no more folds can be seen in the
material.
Note: When you press with your thumb against
each air chamber it should still give a little.
2. To check the operating pressure of the two up-
per side chambers, , place the control
ruler (11) over the measuring strip (1h) on the
inside of each upper air chamber (fig. N).
The lower arrow and the 0 on the control ruler
(11) must overlap the lower arrow and the 0
on the measuring strip (1h).
3. When inflating for the first time the number 10
on the measuring strip (1h) may NOT exceed
position A on the control ruler (11).
Note: The number 10 on the measuring strip
(1h) indicates the maximum expansion of the air
chambers.
4. With repeated inflations the number 10 of the
measuring strip (1h) must be between position
A and position 10 on the control ruler (11).
Attachment of accessories
Note: Secure the cords of the duffel bag and
seat with a reef knot (fig. C).
GB/IE
… 18 …


Need help? Post your question in this forum.

Forumrules
1

Forum

crivit-inshore-335-vii-ian-311071

Reset search

  • Is there any way to get replacement parts as I have misplaced some. Submitted on 30-5-2023 at 22:56

    Reply Report abuse

  • Is there any way of getting some replacement parts as I have misplaced some of them Submitted on 30-5-2023 at 22:55

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit Inshore 335 VII IAN 311071 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit Inshore 335 VII IAN 311071 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info