735864

Crivit Inshore 335 VII IAN 311071 Manual

17
Zoom out
Zoom in
Previous page
1/54
Next page
19GB/IE
Assembly
Follow the individual assembly steps
in the order indicated. If the correct
sequence for inflating the five air cham-
bers is not followed the pressure may
be distributed unevenly. This can lead to
instability of the kayak and adversely
affect its handling characteristics.
Note: The side of the kayak with the 3 screw-on
valves is the stern side (1f). The opposite side
(without screw-on valves) is the bow side (1g).
• Assembly should always be performed by two
adults because of the product’s size.
• Select a smooth and clean surface with
enough space to unfold the kayak. Check
that all the individual parts are present and in
good order and condition.
• When assembling the kayak for the second
and subsequent times, you should inspect
for any possible damage, holes, and tears
and these should be sealed as described in
the section “Repairs”. Once you are on the
water it is no longer possible to remedy any
damage.
• Do not over-inflate the air chambers so as not
to overstretch the plastic foil.
• Make sure that the inflated kayak does not
come into contact with stones or other sharp
objects and become damaged.
Assembling the 2-way screw-on
valve (fig. H)
The floor chambers and the upper side cham-
bers , of the kayak are all provided with a
threaded opening for the screw-on valves (10).
1. Pull the loop (10a) of the valve over the
threaded opening (1c) so that it loops tightly
around the edge of the threaded opening.
2. Turn the base (10b) clockwise into the thread-
ed opening.
Inflation
WARNING!
• Follow the correct sequence when inflating the
air chambers. The correct sequence is indicat-
ed on the kayak and in the instructions for use
(No - ).
• The recommended operating pressure is
0.05bar ( = 50mbar = 0.73psi).
• Avoid inflating the air chambers too much
because there is the risk of over-stretching the
welded seams or even tearing them open.
• To inflate the product use standard commer-
cial foot pumps or double-stroke piston pumps
with matching adapter attachments, and
where applicable a pressure gauge.
• Do not use a compressor or compressed air
bottle to inflate the product. This can lead to
damage to the product.
• Always inflate all air chambers fully.
Inflation sequence
Inflate the air chambers in the following se-
quence:
1. - Floor chamber with screw-on valve
2. - Lower side chamber with stopper valve
3. - Upper side chamber with screw-on valve
4. - Lower side chamber with stopper valve
5. - Upper side chamber with screw-on valve
Note: The air chambers are marked on the
kayak with the corresponding numbers. ( - )
Filling the air chambers
Note: For the screw-on valve you need a pump
with a conical nozzle with a diameter of approx.
17.5mm (fig. I).
For the stopper valve you need a pump with a
conical nozzle with a diameter of approx.
8.5mm (fig. L).
1. Floor chamber with screw-on valve
1. Open by turning the seal cap (10c) of the
screw-on valve (10) anticlockwise (fig. H).
2. Inflate the floor chamber
using the appro-
priate pump.
3. Check the operating pressure as described in
the section “Checking the operating pressure”.
4. Turn the seal cap (10c) of the screw-on valve
(10) clockwise to close it again.
2. Lower side chambers with stopper
valve
1. Open the valve seal (fig. K).
2. Inflate the lower side chambers
, using
the appropriate pump.
3. Check the operating pressure as described in
the section “Checking the operating pressure”.
… 17 …


Need help? Post your question in this forum.

Forumrules
1

Forum

crivit-inshore-335-vii-ian-311071

Reset search

  • Is there any way to get replacement parts as I have misplaced some. Submitted on 30-5-2023 at 22:56

    Reply Report abuse

  • Is there any way of getting some replacement parts as I have misplaced some of them Submitted on 30-5-2023 at 22:55

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit Inshore 335 VII IAN 311071 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit Inshore 335 VII IAN 311071 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info