750309

Crivit IAN 97694 Inshore 335 Manual

34
Zoom out
Zoom in
Previous page
1/38
Next page
36 GB
This is particularly important when
inflating the five air chambers because
incorrect pressure distribution can lead
to kayak instability and to the interfe-
rence of its handling characteristics.
1. Select a smooth, clean surface with sufficient
space to unpack and unfold the kayak.
Make sure that all of the individual parts are
present and in a flawless state.
2. From the second assembly onwards, the kayak
should be checked for possible damage.
Inspect for holes and tears, and seal any that
you find, as described later. You cannot repair
any damage once you are afloat.
Assembling the double
paddle (Fig. E)
Note:
The paddle can be converted into a single blade
paddle by removing the paddle centre section
for when 2 occupants are present.
• First push both drip-rings over both ends of
the paddle tubes so that they sit below the
push button on the taper of the pipe. Then
connect both paddle tubes with the centre
section so that both push buttons engage
audibly and visibly.
Assembling the screw valve
(Fig. F)
The upper side chambers of the kayak /
are each equipped with a threaded opening for
the attached screw valve.
Pull the loop of the valve over the threaded
opening so that it is firmly placed in the
groove intended for it. This process requires
sensitivity and patience, however, this must be
carried out carefully so that there is no chance of
the valve coming free of the opening later on.
Now turn the base firmly in a clockwise
direction into the threaded opening.
Inflating
WARNING!
• Follow these directions in the correct,
consecutive order when inflating the air
chambers.
• The recommended operating pressure is
0.05 bar (= 50 mbar = 0.73 psi).
• Avoid excessive inflating of the air chambers
to prevent the danger of the material
stretching or the seams tearing.
• Use a standard foot pump for inflating the
article or a double stroke piston pump with the
corresponding connection and a manometer if
necessary.
• Do not use a compressor or a compressed
air bottle to inflate the article because this can
cause article damage.
• Always completely inflate all of the air
chambers.
Inflation sequence (Fig. G)
Inflate the air chambers in the following
sequence:
1. Floor chamber with stopper
valve
2. Lower side chamber with stopper
valve
3. Upper side chamber with screw
valve
4. Lower side chamber with stopper
valve
5. Upper side chamber with screw
valve
= as marked on the boat
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit IAN 97694 Inshore 335 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 97694 Inshore 335 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info