736616

Crivit IAN 96716 Manual

17
Zoom out
Zoom in
Previous page
1/20
Next page
17GB
Avoid damage to property!
• Do not erect the tent so that the tent entrance
is in the direction of the wind. Wind could
damage the tent.
• All the tent materials suffer material fatigue
and bleaching if they are exposed to
prolonged, strong sunlight. For this reason,
when the tent is to be used over longer
periods, erect it in a shady position.
Do not leave the tent assembled
unnecessarily.
Assembly
NOTE!
Perform a test assembly before the camping trip.
In doing so, ensure that all the accessories are
present.
Selecting a location for
placing the tent
Choose a place that is as flat and clean as
possible. Avoid dips in the ground.
Remove stones, branches and other sharp ob-
jects in order to prevent damage to the tent floor.
Use natural shade, such as hedges, rocks, etc.
Use the appropriate pegs for sandy ground in
order to prevent accidental loosening of the
tension.
NOTE!
Insert the pegs into the ground at a slight angle
to achieve good strength but without causing
tension in the tent surface. The tent material and
tension points should only be slightly taut, so that
it can compensate for pressure from the wind.
Ensure that there is not too much pressure on the
tent. Check the tent tension according to weather
condition.
NOTE!
Water condensation occurs basically in every
tent, however particularly during strong fluctu-
ations in temperature. After a night in the tent,
there will be drops of condensation on the inner
wall. Condensation is not evidence of leakiness.
Good ventilation reduces condensation in the
tent.
1. Spread the base of the inner tent flat on the
ground, close the zips for the entrance and fix
the loops at all four corners with the pegs
(Fig. B).
2. Build together the segments of the tent poles
(3) and (4). Slide the two black tent poles (3)
diagonally through the loops in the middle of
the inner tent (Fig. C). Secure the inner tent on
the tent poles using the clips (Fig. D).
3. Turn the tent around and insert the metal pins
at the corners of the inner tent into the end
of the tent poles so that these are under
tension (Fig. E).
4. The storage net (9) can now be hooked onto
the roof ridge in the interior of the inner tent
(Fig. F).
5. Place the outer tent over the inner tent
(Fig. G). Secure the outer tent using the bands
to the tent poles and at the crossing point in
the frame. Push the grey tent poles (4) through
the frame tunnel in the outer tent (Fig. H).
Right the frame up and insert the metal pins
from the corners of the inner tent into the end
of the tent poles. Secure the outer tent with
10 pegs and ensure that the loops at the four
corners are fixed with the pegs of the inner
tent (Fig. I).
6. Secure each of the 6 guy ropes with a peg.
The length of the guy ropes can be adjusted
with the tensioner (Fig. J).
Disassembly
NOTE!
Disassemble the tent, if possible, when clean
and dry to prevent the formation of mould and
mildew. After disassembling in rain, immedia-
tely dry the tent. Clean all the parts thoroughly
before packing them away.
• Remove the pegs and guy ropes.
• Remove the tent poles, fold them together
and disassemble the inner and outer tents.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit IAN 96716 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 96716 in the language / languages: French, Italian as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Crivit IAN 96716

Crivit IAN 96716 User Manual - English, German, Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info