Manual Crivit IAN 368918 (page 11 of 36) (English, German, Dutch, Danish, French, Polish, Spanish)

785740

Zoom out

Zoom in

1/36

11GB/IE

Assembly

The product is supplied folded up in transport

condition. Proceed as follows to get it ready for

riding:

Unfolding (Fig. A)

1. Pull the safety lever (1) upwards and hold it.

2. Pull the lever (2) upwards, then release the

safety lever (1) and fold the steering col-

umn (3) forwards until it locks into place.

Mounting the grips (Fig. B)

1. Remove the grips (4) from the brackets (5).

2. Lift the cover flap (6).

3. Press the locking knobs (7) down on the grips

and push the grips on both sides into the

T-tube (8) of the steering column. The locking

knobs must snap audibly into place into the

holes (9) provided.

4. Press the cover flap (6) down over the locking

knobs.

Adjusting the height of the steering

column (Fig. C)

The steering column can be adjusted to four

different heights. The product may only be used

if the locking knob is locked in place into one of

the four holes provided and the steering column

is then secured with the quick release fastener!

1. Loosen the quick release (10) on the steering

column.

2. Pull the steering column (3) upwards, until the

locking knob (11) locks into place in one of

the four holes (12).

3. Secure the steering column by locking the

quick release (10).

Note: If the quick release does not fit snugly on

the steering column when tightening, tighten the

knurled screw firmly with the enclosed Allen key.

Make sure that the quick release fastener is

secured before tightening.

Steering head bearing (Fig. F)

The steering head bearing (18) is pre-set when

the product is supplied. If, after a while, the

handlebars have too much play or become too

stiff, get the steering head bearing adjusted by a

specialist dealer or at a bicycle shop.

Putting the product into

transport condition

1. Loosen the quick release (10) on the steering

column and press the locking knob (11)

(Fig. C).

2. Push the steering column (3) all the way down

and lock the quick release (10) (Fig. C).

3. Lift the cover flap (6) (Fig. B).

4. Press the locking knobs (7) of the grips and

pull the grips (4) out of the T-tube (8) (Fig. B).

5. Attach the grips to the brackets (5) (Fig. B).

6. Pull the safety lever (1) upwards and hold it.

Pull the lever (2) upwards, then release the

safety lever (1) (Fig. D).

7. Press the steering column towards the deck

until it locks into place (Fig. D).

Use

Riding, braking, parking (Fig. E)

• Put one leg on the deck (13) and give momen-

tum by regularly pushing off with the other leg.

• Step on the brake plate (14) to brake.

• Swing out the stand (15) to park. The product

may only be parked on a level surface.

Maintenance

Replacing the rollers (16)/(17) (Fig. H)

Important!

Pay attention to the chapter on “Technical data”.

Rollers that have a different diameter, may

alter the riding properties and could possibly

endanger the user. Do not use rollers that cannot

be installed properly. Never use rollers that are

larger than the original rollers on the product.

Rollers wear out. This wear depends on many

factors, such as, for example, the terrain, the size

and weight of the user, the weather conditions,

the material of the rollers and their hardness, etc.

It is necessary to replace them now and then.

1. Loosen the axle bolts (21)(22) with two size 5

Allen keys.

2. Pull out the axle bolts and remove the roller.

3. Install the new roller (16) or (17) and secure it

with the axle bolts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 368918 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit IAN 368918 Manual

Product: