Manual Crivit IAN 347012 WR 8221 (page 16 of 42) (English, German, Dutch, French, Polish, Swedish)

750298

Zoom out

Zoom in

1/42

Note: make sure that the sensor cables are firmly

connected to ensure reliable signal transmission.

3. Carefully insert the sensor cables into the hole

provided in the base frame.

4. Fasten the computer to the base frame with

the previously removed screws (1a).

Note: make sure that the sensor cables do not

get caught on anything.

Folding up the product (Fig. F)

Fold the product up if you are not using it.

1. Slide the seat (3) forwards.

Note: make sure that the seat is completely

slid forward, and that it cannot move when the

product is being folded up.

2. Loosen the locking screw (14), the washer

(15) and the locking pin (9).

3. Fold the slide rail (2) vertically upwards.

4. Secure the slide rail with the locking pin (9).

5. Fasten the locking screw (14) and the washer

(15).

Note: the product has wheels (1d) on the right

and left of the front foot of the base frame. Lift

the product from the back foot until the wheels

touch the ﬂoor, and slide the product to the

desired spot.

6. Perform this procedure in reverse to unfold the

product again.

Note: hold the slide rail ﬁrmly when you are

fastening or removing the locking pin!

Using the product

Filling the water tank

Before you start training, ﬁll the water tank with

mains water. Proceed as follows:

1. Remove the seal on top of the water tank.

2. Place a large bucket of mains water next to

the product and insert the stiff end of the hand

pump into the bucket.

3. Insert the flexible hose of the hand pump into

the water tank.

Note: make sure that the ventilation tube at the

upper end of the hand pump is closed before

you start filling the tank.

4. Fill the water tank with max. 12l of mains

water by pressing the hand pump together.

Note: pay attention to the fill level indicator on

the water tank when filling the tank. The maxi-

mum fill level must not be exceeded!

5. Once you have reached the desired fill level,

open the ventilation tube on the upper end

of the hand pump so that excess mains water

can flow out from the hand pump.

6. Place the seal back on top of the water tank.

Note: the more water you use, the greater the

resistance and the more strenuous the exercise

will be. Note that excessive resistance can lead

to adverse effects on your health.

Emptying the water tank

Remove the water tank if you will be storing or not

using the product for an extended period of time.

1. Remove the seal on top of the water tank.

2. Insert the stiff end of the hand pump into the

water tank.

3. Place a large bucket next to the product and

insert the flexible hose of the hand pump into

the bucket.

Note: make sure that the ventilation tube on the

upper end of the hand pump is closed before

you begin emptying the tank.

4. Pump the mains water into the bucket by press-

ing the hand pump together.

5. Open the ventilation tube on the upper end

of the hand pump so that excess mains water

can flow out from the hand pump.

Note: dispose of the mains water that has been

pumped out!

6. Place the seal back on top of the water tank.

Adjusting the footrests (Fig. J)

Before you start training, adjust the footrests

(1b), (1c) to the appropriate size for your feet.

1. Pull the movable part of the footrest upwards

to reduce the foot surface area. Pull the mov-

able part of the footrest downwards to extend

the foot surface area.

2. Tighten the strap tightly enough so that your

foot cannot slip.

Note: the strap must be above the balls of your

feet to guarantee a secure footing.

Using the holder (Fig. I)

1. Pull the clip (5o) on the computer (5) upwards

with one hand.

2. Use your other hand to place your smart-

phone or tablet into the holder.

3. Fasten your smartphone or tablet with the clip.

Operating the computer

The product meets accuracy grade C, i.e., there

is no claim to accuracy of the computer displays.

Note: remove the plastic film from the display

of the computer (5).

Setting the date and time (Fig. G)

Once the batteries have been inserted into the

computer, a signal tone will sound and the com-

puter (5) will display the date and time as well

as the current temperature in the room.

Use the buttons (5j/5m) to set the date (year/

month/day) and the time, and press the button

(5l) to confirm the respective inputs.

Turning the product on and off

• When you start exercising, or pull strongly

on the pull rod, the computer switches on

automatically. The training display is shown

(all parameters are at 0).

• If the product is not used for approx. 4 min-

utes, the temperature, date and time are dis-

played. The computer turns off automatically

after a short time. Press any button to display

the temperature, date and time again. Press

the button again to access the training display.

Training display (Fig. G)

The following information and respective functions

are shown on the display of the computer (5):

• settings (5a), which can be adjusted manually

• distance travelled (5b) from 0.00 to 99.00 in km

• pulse (5c) from 0 to max. 240 BPM

Note: the computer has a receiver for uncoded

5kHz chest straps to ensure accurate and

constant pulse measurement. The chest strap (not

included in the package contents) automatically

connects to the computer and transmits the heart

frequency wirelessly.

• beats per minute (5d) from 0 to 99 BPM

• calory consumption (5e) from 0 to 999.0cal

Note: the calculation is based on pre-programmed

standard values that serve as a guideline only.

• total beats (5f) from 0 to 9990

• average time (5g) required to travel 500m,

from 00:00 to 99:00/500m

• alternating display of the respective values

during training (5h)

Button functions (Fig. G)

• Press the button (5i), once your pulse is detect-

ed, to measure your performance.

Note: your performance can only be measured

if you are using a chest strap (not included in

the package contents). Press the button once

your pulse is detected. A one-minute countdown

starts. After the countdown, the display will show

a performance grading.

• Press the button (5j) to increase the values

during input. You can increase the values in

increments of 10.

• Press the button (5k) to reset a selected value.

• Press the button (5l) to confirm the input.

• Press the button (5m) to decrease the values

during input. You can decrease the values in

increments of 10.

• Press the button (5n) to reset all settings.

The following performance levels appear on

the display after your performance has been

measured:

• F1: outstanding

• F2: good

• F3: normal

• F4: moderate

• F5: poor

• F6: very poor

Selecting the training mode

Choose between the individual training mode or

the goal-setting mode.

Individual training mode

Complete an individual training session by

starting the workout directly. You do not have to

enter any value settings. The computer continu-

ously records your values during the exercise.

Goal-setting mode

In goal-setting mode you can set the values for

total beats (5f), average time (5g), distance trav-

elled (5b), calorie consumption (5e) and pulse

(5c), in that order. Proceed as follows to set the

target values:

1. Press the button (5j) to move around the

computer display.

2. Press the button (5j) to increase a value. Press

the button (5m) to decrease a value.

3. Confirm your selection with the button (5l).

4. Start the workout.

Note: a set target value is counted down to 0.

Values that are not set increase during the work-

out until they reach the upper limit.

General training instructions

• Wear comfortable sportswear.

• Warm up before each training session and

end the session gradually.

• Take suﬃcient breaks between the exercises

and keep yourself suﬃciently hydrated.

• If you are a beginner, never train with too

much intensity. Increase the intensity of the

training sessions slowly.

• Perform all exercises smoothly, not jerkily or fast.

• Be sure to breathe steadily. Exhale during

exertion and inhale upon release.

• Maintain correct body posture while exercising.

• Make sure that your feet are optimally placed

on the treads.

GB/IE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Crivit IAN 347012 WR 8221 in the language / languages: English, German, Dutch, French, Polish, Swedish as an attachment in your email.

The manual is 5,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Crivit IAN 347012 WR 8221 Manual

Product: