736622

Crivit 7769 11500 IAN 106627 Manual

9
Zoom out
Zoom in
Previous page
1/61
Next page
9 GB/IE
Operation / Tips for the best cooling ... / Exchanging the... / Troubleshooting
Turn the cooling output switch
3
to the “OFF”
position. This turns the coolbox off.
Note: If you want to reach a Delta T (Delta T =
difference between outside temperature and inside
temperature) of up to 17 °C and thereby a lower
inside temperature than is possible in the “eco” nor-
mal operation, turn the cooling output switch
3
to
the “MAX” position. Please note that in this case
more energy will be consumed than in normal
operation.
After the operation with 230 V function has been
completed, disconnect the mains plug from the
socket.
Function with 12 V operation
CAUTION! The temperature controller on the
front of the lid is only suited to 230 V operation
and it does not function in 12 V operation.
When operating with a 12 V power supply, the
cooling unit always produces a temperature
difference from the ambient temperature of up
to 17 °C. The cooling output can not be con-
trolled by means of the temperature controller
on the front of the lid.
Tips for the best cooling output
and energy saving
Select a well ventilated location protected from
sunshine.
Only place pre-cooled contents into the cool-
box.
Do not open the coolbox longer than necessary.
Don’t leave the lid open longer than necessary.
Ensure that the coolbox is not packed too
full and that the air can circulate adequately
between the coolbox contents.
In order that a high level of energy saving can
be achieved, normal operation (cooling output
switch
3
in the “eco” position) is recom-
mended for longer periods of use in 230 V
operation.
Exchanging the 12 V fuse
See also fig. C.
To replace the 12 V fuse
10
, unscrew the red
adjustment sleeve
7
from the plug, turning
counter-clockwise.
Unscrew the screw
5
with a suitable Phillips
screwdriver from the top half of the housing
6
.
Lift the top half
6
of the housing from the bot-
tom half
9
.
Lift the contact pin
11
carefully out of the hous-
ing section. The fuse
10
can now be removed.
Note: If the thin metal connection in the mid-
dle between the two metal caps is broken, then
the fuse
10
is defective and must be replaced.
Press the contact spring
8
backwards and
insert the new fuse
10
carefully into the groove
provided for it. Now place the rear edge of the
contact pin
11
on the front metal cap of the fuse
10
. By releasing the contact spring
8
, the fuse
10
and contact pin
11
are located in the groove.
Screw the top and bottom halves of the housing
6
9
together again, reattach the red adapter
sleeve
7
and turn clockwise to tighten. The plug
is now ready for operation.
Troubleshooting
In the event of a malfunction, first verify you cor-
rectly followed the instructions for using the cool
box. Also check:
– Is the connection cable correctly connected
and does your car cigarette lighter / domestic
socket function properly?
– Have you set up the coolbox in such a way
that the air can circulate freely and that venting
of the cooling unit can occur?
– Is the fuse in the plug of the 12 V connection
cable OK?
– Check the position of the cooling output
switch
3
on the front of the lid.
If you can not rectify the malfunction on your own,
please contact our Customer Service (see chapter
on “Service”).
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Crivit 7769 11500 IAN 106627 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Crivit 7769 11500 IAN 106627 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info