618062
22
Zoom out
Zoom in
Previous page
1/42
Next page
179
shown on the display by a segmented indicator at the bottom
on the right, which functions according to following table:
If, during surfacing, the maximum allowed ascent rates are
exceeded, the display will show different segments, showing
the ascent rate increasing level. Additionally, the alarm will
sound, the UFDS display will start flashing ( ) icon (picture
17), as well as the flashing segmented ascent rate and cur-
rent depth value indicator.
In this situation, surfacing must be stopped until the ( ) icon
disappears and the computer shows its normal display.
DANGER: Surfacing too fast dramatically increases the
risk of air embolism. Cressi-sub recommends that at the
end of each dive, engage in a "safety stop" of 3-5 minutes
at 10 ft– 20 ft., which will be assisted by the computer (see
chapter 3.4.2
WARNING: Do not engage in a follow up dive after a surfa-
ce interval if the ( ) icon has been on! The computations
for the next dive might be invalidated by exceeding the maxi-
mum ascent rate.
Related topics:
2.5.3. - Units of measure setting.
3.4.2. - Safety stop.
4.1.2. - Logbook.
3.4.2. – Safety Stop ( ).
Archimedes II is automatically programmed to signal a safety
stop after each dive at a greater depth than 32 ft., as recom-
mended by training agencies and the most recent studies on
diving physiology. A stop should be carried out at a depth
between 10 ft – 20 ft., and to last as long as signalled by the
computer.
NOTE: Cressi-sub recommends that after each dive, a safety
stop of 3-5 minutes at 10 – 20 ft be conducted.
The stop is indicated on the display by the ( ) icon (pic-
ture 18); on such occasion, the display indicates how many
minutes the stop must last and the depth at which it has to be
conducted.
Although the safety stop is not mandatory, they are highly
recommended. In the event that ascent rates have been
exceeded, additional safety times should be conducted.
DANGER: It is very important that ascent rates be care-
fully monitored after a safety stop. Rapid ascent rates, after
a safety stop, are very dangerous and can result in air
embolism.
Related topics:
2.5.3. - Units of measure setting.
3.4.1. - Surfacing speed.
3.4.3. – Decompression forewarning.
Any time the available no decompression time shown by the
“ ” display decreases to 3 minutes (picture 19), Archimedes
II will engage an alarm and the display flashes for several
seconds notifying the diver that they are approaching no
Depth
0ft
19.3ft
19,7ft
58.7ft
59ft
5ft
No segment
0.0 ft -
12.8 f/min
0.0 ft -
19.3 ft/min
0.0 m -
25.9 ft/min
1 segment
13.1 ft/min -
19.3 ft/min
19.7 ft/min -
25.9 ft/min
26.2 ft/min -
36 ft/min
2 segments
19.7 ft/min -
25.9 ft/min
26.2 ft/min -
39 ft/min
39.4 ft/min -
52.1 ft/min
3 segments
26.2 ft/min
()
39.4 ft/min
()
52.4 ft/min
()
ENGLISH
Manuale ARCHIMEDE II 2008:Manuale 6 26-06-2008 8:26 Pagina 179
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cressi Archimede II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cressi Archimede II in the language / languages: English as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info