818989
6
Zoom out
Zoom in
Previous page
1/191
Next page
5 MAINTENANCE
IMPORTANT
Read and understand the safety regulations and the
maintenance instructions before you clean, repair or do the
maintenance work on the machine.
IMPORTANT
Make sure that all nuts, bolts and screws are tight. Check
regularly that the handles are firmly mounted.
IMPORTANT
Use only the replacement parts and accessories of the initial
manufacturer.
5.1 GENERAL INFORMATION
IMPORTANT
Only your dealer or approved service center can do the
maintenance that is not given in this manual.
Before the maintenance operations:
Stop the machine.
Remove the battery pack.
Cool the motor.
Store the machine in a cool and dry place.
Use correct clothing, protective gloves and safety glasses.
5.2 CLEAN THE MACHINE
Clean the machine after each use with a moist cloth
dipped in neutral detergent.
Do not use aggressive detergents or solvents like "glass
cleaner" to clean the plastic parts or handles.
Keep the trimmer head free from grass, leaves, or
excessive grease.
Keep the air vents clean and free of debris to avoid
overheating and damage of the motor.
Do not spray water onto the motor and electrical
components.
5.3 REMOVE THE REMAINING LINE
Figure 9 - 11.
1. Simultaneously press the tabs on the sides of the trimmer
head.
2. Pull and remove the spool cover.
3. Remove any remaining line.
4. Clean dirt and debris from all parts.
5. Align the spool tabs with the tab openings in the base of
the spool.
6. Push the spool cover until it clicks into position.
5.4 INSTALL THE CUTTING LINE
Figure 12 - 15.
NOTE
Do not put more than 15 feet of cutting line in at a time.
1. Line up the slots on the spool cap with the slots on the
trimmer head.
2. Put the cutting line through the hole. Push the cutting line
until it exits the opposite hole.
3. Pull the cutting line through until there is an equal
quantity of cutting line on each side.
4. Turn the spool cap clock-wise to wind the cutting line
into the trimmer head. Keep approximately 5 in of cutting
line above out of each side of the trimmer head.
5.5 REMOVE THE TRIMMER HEAD
Figure 16.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Turn the trimmer head clockwise to loosen it. Do not
remove the spacer from the shaft.
5.6 ASSEMBLE THE TRIMMER HEAD
Figure 16.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Assemble the trimmer head.
3. Turn the trimmer head counterclockwise to tighten it.
4. Remove the metal rod.
IMPORTANT
You must install the cut-off blade when you use the trimmer
head.
6 TRANSPORTATION AND
STORAGE
6.1 MOVE THE MACHINE
When you move the machine, you must:
Wear gloves.
Stop the machine.
Remove the battery pack and charge it.
Assemble the blade guard.
6.2 STORE THE MACHINE
Remove the battery pack from the machine.
Make sure that children cannot access the machine.
Keep the machine away from corrosive agents such as
garden chemicals and de-icing salts.
6
English
EN
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82T15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82T15 in the language / languages: All languages as an attachment in your email.

The manual is 3.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info