818974

Cramer 82LT107 Manual

14
Zoom out
Zoom in
Previous page
1/340
Next page
Error Code Description Solution
NA Display communication error Please check the display's connecting parts and CAN net-
work.
Incorrect display selected Please select the correct display for your vehicle model
7 MAINTENANCE
7.1 MOWER BLADE MAINTENANCE
Check the mower blades daily. They are the key to power efficiency and well-groomed turf. Keep them sharp -- a dull
blade will tear rather than cut the grass, leaving a brown ragged top on the grass within a few hours. A dull blade also
requires more power. Replace any blade that is bent, cracked or broken.
WARNING
Never attempt to straighten a bent blade by heating, or weld a cracked or broken blade as the blade may break and
cause serious injury. Replace worn or damaged blades.
WARNING
Never work with blades while key is in the ignition switch. Turn key to “OFF” position, remove the battery packs
from the machine. Block up mower when you must work under it. Wear gloves when handling blades. Always check
for blade damage if mower strikes a rock, branch or other foreign objects!
DANGER
Touch-up sharpening can be done with a file. Check the blades for balance following grinding. A commercial
balancing tool is available through most hardware supply stores, or balancing can be done by placing the blade on
an inverted line punch or 12.7mm (1/2") bolt. Blade should not lean or tilt. While spinning the blade slowly, it should
not wobble. If blade is out of balance, true it up before reinstalling. Lay the blade on a flat surface and check for
distortion. Replace any distorted blade.
WARNING
• The blade sail (curved part) must be pointing upward toward the inside of the deck to ensure proper cutting.
• When mounting blades, rotate them after installation to ensure blade tips do not touch each other or sides of the
mower.
• Failure to correctly torque the bolt may result in the loss of the blade, which can cause serious injury.
• Mower blades are sharp and can cut. Wear gloves and use extra caution when servicing them.
7.1.1 REPLACE THE BLADE
See figure 17
1. Stop the motor, remove the start key, and set the parking brake.
2. Raise the height of the cutting deck to its highest position to allow access to blades.
NOTE
If necessary, raise the mower by placing on a lift or using a jack and jack stands, or remove the cutting deck as
described in the previous section to gain access to the blades.
WARNING
If raising the mower to access the blades, make sure the mower is properly secured and the parking brake is
set before proceeding. Failure to properly secure the mower could cause it to fall, resulting in death or possible
serious personal injury.
3. Wedge a block of wood between the blade and mower deck to prevent the blade from turning.
4. Loosen the blade nut by turning it counterclockwise (as viewed from bottom of mower) using a 16 mm wrench or
socket (not provided).
14
English
EN
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82LT107 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82LT107 in the language / languages: All languages as an attachment in your email.

The manual is 7.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info