818993
11
Zoom out
Zoom in
Previous page
1/309
Next page
11
cramer.eu
EN
and do not operate this product until all missing or damaged parts are replaced.
Please call Customer Service for assistance.
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to
damage from various types of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING!
Do not at any time let brake liquids, gasoline, petroleumbased
products, penetrating oils, etc.,come in contact with plastic parts.
Chemicals can damage, weaken or destroy plastic which may
result in serious personal injury.
Only the parts shown on the parts list are intended to be repaired or replaced by
the customer. All other parts should be replaced at an authorised service centre.
STORAGE
Storing the product
Remove the battery pack from the unit before storing.
Clean all foreign material from the unit.
Store it in a place that is inaccessible to children.
Keep away from corrosive agents such as garden chemicals and de-icing
salts.
Store and charge your batteries in a cool area. Temperatures above or below
normal room temperature will shorten battery pack life.
Never store batteries in a discharged condition. Store battery packs in a
30%- 50% charged condition.
Store the battery pack where the temperature is between 0-23* C and
away from moisture.
All batteries gradually lose their charge. The higher the temperature, the
quicker they lose their charge. If you store your unit for long periods of time
without using it, charge the pack as normal every six months of storage.
This practice will prolong battery pack life.
Troubleshooting
PROBLEM PROBABLE CAUSE POSSIBLE SOLUTION *
Bar and
saw chain
running
hot and
smoking.
Check saw chain tension for
overtightened condition. Tension saw chain.
No oil in the oil tank. Refill oil into the oil tank.
The discharge port is
blocked by debris.
Refer to the manual to remove
the bar and clean out the debris.
Oil tank is blocked by
debris.
Clean out the oil tank and refill
with clean oil.
Bar and chain oil tank cap is
blocked by debris. Clean the debris off the oil cover.
The sprocket or guide wheels
is clogged with debris.
Clean and remove debris from
sprocket and guide wheel.
Motor
runs, but
chain is not
rotating.
Saw chain tension is too
tight.
Refer to Saw Chain Tension
Guide earlier in this manual.
Check guide bar and saw
chain assembly.
Refer to Replacing the Bar and
Saw Chain assembly earlier in
this manual.
Check guide bar and saw
chain for damage.
Remove the battery from the
unit. Take the bar cover off,
and remove the bar and saw
chain. Clean all debris from the
chain saw. After all debris is
cleared, insert battery and run
the chain saw. If the sprocket is
spinning your motor is okay. If
the sprocket is not spinning, call
customer service.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS15 in the language / languages: All languages as an attachment in your email.

The manual is 5.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info