818993
7
Zoom out
Zoom in
Previous page
1/309
Next page
7
cramer.eu
EN
31. Keep work off ground leave support limbs until log is cut
32. Log supported along the entire length
33. Cut from top (over buck) avoid cutting earth
34. Log supported one end
35. Under buck 36. Over buck
37. Log supported both ends
38. Bucking a log
39. Stand on uphill side when cutting because log may roll
40. Wrench
Batteries and Battery Charger
See the battery and charger manual.
Assembly
WARNING!
To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the tool when
assembling parts.
This chain saw requires assembly.
1 Unscrew the sprocket cover tighten nuts and remove the sprocket cover.
2 The saw chain should face in the direction of chain rotation. If they face
backwards, turn the loop over.
3 Place the chain drive links into the bar groove.
4 Position the chain so there is a loop at the back of the bar.
5 Hold the chain in position on the bar and place the loop around the sprocket
and make sure it is correctly mounted. Make sure the bar hole fits well with
bolt for saw chain tension.
6 Replace the sprocket cover, turn the chain tension adjust bolt clockwise
until the saw chain is properly tensioned. The guide bar must then be
pushed upwards, check chain tension again, do not tension the chain too
tight.
7 After the chain is well-tensioned, tighten the nuts again.
NOTE: The saw chain is properly tensioned if, in the middle of the guide bar, it
can be lifted 3mm to 4mm from the edge of the guide bar. Start the saw again
with a new saw chain, allowing it to run-in for 2~3 minutes.
To Install/ Remove the Battery
To Install (see Figure 2)
1 Align the battery pack with the battery compartment on the chain saw.
2 Grasp the chain saw firmly.
3 Push the battery pack into the battery compartment until the latch locks
into place.
4 You should hear a ”click” once the battery is installed.
To Remove (see Figure 2)
1 Press the battery release button on the chain saw.
2 Grasp the chain saw firmly and pull the battery out of the handle.
Operation
Before each use check the saw chain tension
Pull the saw chain in the middle of the lower side of the bar away from the
bar. The gap between the cutter in the saw chain and the bar should be
between 3mm - 4mm.
If you need to adjust the saw chain tension, please refer to the section
ADJUSTING THE CHAIN TENSION” later in this manual.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cramer 82CS15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cramer 82CS15 in the language / languages: All languages as an attachment in your email.

The manual is 5.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info