Manual Corbero CLVG4508X (page 40 of 42) (English, Spanish)

743175

Zoom out

Zoom in

1/42

Once the appliance has been installed, the power supply cable and the electrical socket should

be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced by the manufacturer or its Technical

Assistance Service in order to prevent all potential hazards.(See Assistance)

The company shall not be held responsible for any incidents that occur if these regulations are

not observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before running the first wash cycle, completely

fill the salt dispenser with and add approximately 1.2 Kg of salt (see Rinse aid and refined salt). The

water may overflow: this is normal and is not a cause for concern. It is also normal that the LOW

SALT indicator light continues to flash for a few cycles after the salt has been loaded.

Positioning the Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and

the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and

drain hoses that can be positioned to the right or the left to facilitate proper installation.

Leveling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the

dishwasher, making it level. In any case, the appliance should not be inclined more than 2 .

NOTE: The maximum adjustment height of the feet is 20 mm.

How to Drain Excess Water From Hoses

If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly

into the sink. It will be necessary to drain excess water from hoses into a bowl or a suitable

container that is held outside and lower than the sink.

Water Outlet

Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.

Ensure that the water inlet hose is not kinked or squashed.

Extension Hose

If you need a drain hose extension, observe to use a similar drain hose..

It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be

reduced.

Syphon Connection

The waste connection must be at a height of between 50cm (minimum) and 100cm (maximum)

from the bottom of the dish. The water drain hose should be fixed by a hose clip.

Attention

The followings should be checked before starting the dishwasher:

1 Whether the dishwasher is level and fixed

2 Whether the inlet valve is opened

3 Whether there is leakage at the connections of the conducts

4 Whether the wires are tightly connected

5 Whether the power is switched on

6 Whether the inlet and drain hoses are knotted

7 All packing materials and printings should be taken out from the dishwasher

After installation, please put this manual into the bags of printings.

The content of this manual is very helpful to the users.

Start of Dishwasher

9. Troubleshooting Tips

Error codes

When some malfunctions happen, the appliance will display error codes to warn you.

WARNING!

If overflow occurs, turn off the main water supply before calling a service. If there is water in the base

pan because of an overfill or small leak, the water should be removed before restarting the

dishwasher.

Codes

Meanings

Possible Causes

Water drainage malfunction

Door open

Water inlet

Water drainage

Temperature sensor

Overflow/leakage

Water leakage

Heating element

The door is opened when the

dishwasher is operating

Water inlet malfunction

Temperature sensor malfunction

Overflow occurs/Water leakage occurs

Water leakage occurs

Abnormal heating

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Corbero CLVG4508X in the language / languages: English, Spanish as an attachment in your email.

The manual is 11,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Corbero CLVG4508X Manual

Product: