Manual Corbero CLVG4508W (page 32 of 42) (English, Spanish)

743174

Zoom out

Zoom in

1/42

4 Prior Using for the First Time

Before using your dishwasher for the first time:

A. Set the water softener

B. Loading the salt into the softener

C. Fill the rinse aid dispenser

D. Fill in detergent

A. Set the Water Softener

The water softener is designed to remove minerals and salts from the water, which would have a

detrimental or adverse effect on the operation of the appliance. The higher the content of these

minerals and salts, the harder the water is. The softener should be adjusted according to the

hardness of the water in your area. Your local Water Authority can advise you on the hardness of

the water in your area.

B. Loading the Salt into the Softener

Always use salt intended for use with dishwasher.

NOTE: If your model has no water softener, you may skip this section

WATER SOFTENER

The hardness of the water varies from place to place. If hard water is used in the

dishwasher, deposits will form on the dishes and utensils.

The appliance is equipped with a special softener that uses salts specifically

designed to eliminate lime and minerals from the water.

A. Remove the lower basket and then unscrew and remove the cap from the salt container.

B. If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).

The salt container is located beneath the lower basket and should be filled as follows:

Attention!

Only use salt specifically designed for use in dishwashers! All other types of salt not specifically

designed for use in a dishwasher, especially table salt, will damage the water softener. In case of

damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is

liable for any caused damages.

Only fill with salt just before starting one of the complete washing programmes.

This will prevent any grains of salt or salty water, which may have been split, remaining on the

bottom of the machine for any period of time, which may cause corrosion.

After the first wash cycle the control panel light expires.

Front View

1 Upper Basket

2 Spray Arms

3 Lower Basket

4 Water Softener

5 Filters

6 Detergent Dispenser

7 Rinse Aid Dispenser

8 Cutlery basket

Dishwasher Features

Setting

The amount of salt dispensed can be set from H0 to H7.

Salt is not required at the set value H0.

1. Find out about the hardness value of your tap water. Your water utility company will help you

with this.

2. Set value can be found in the water hardness table.

3. Close the door.

4. Switch on "Power" switch.

5. Hold down " Delay" button and then press "Program" button for 5 seconds.The buzzer rings

one time and H..

flashes on the digital display.(factory setting is H4)

To change the setting:

1. Press " Delay " button.

Each time the button is pressed, the set value

increasesby one level;when the value of H7 has

been reached, the display jumps back to H0(off).

2. Press " Program " button. The chosen setting

has now been stored.

Water hardness

Clark

Range

Mmol/l

Set value on

the machine

0-8

9-10

11-12

13-15

16-20

21-26

27-38

39-62

soft

medium

hard

0-1.1

1.2-1.4

1.5-1.8

1.9-2.1

2.2-2.9

3.0-3.7

3.8-5.4

5.5-8.9

Water hardness table

Contact your local water board for infor-

mation on the hardness of your water

supply.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Corbero CLVG4508W in the language / languages: English, Spanish as an attachment in your email.

The manual is 11,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Corbero CLVG4508W Manual

Product: