596502

Constructa CM424252 Manual

36
Zoom out
Zoom in
Previous page
1/56
Next page
36
Time program function
This function may be used in two different ways:
■ to automatically switch off a hotplate
■ as a timer
Turning off a hotplate automatically
The zone turns off automatically once the selected time has
elapsed.
Program the cooking time.
1. Select the power level of the desired hotplate with the
appropriate control.
2. Press the 3 symbol. The Ú indicator on the hotplate lights
up. ‹‹ is displayed on the time program function display.
3. Press the + or - symbol. The basic setting appears:
+ symbol: 30 minutes.
- symbol: 10 minutes.
4. Press the + or - symbol until the required cooking time
appears.
After a few seconds, the cooking time begins to elapse.
Note: The same cooking time can be automatically
programmed for the all the hotplates. The programmed time
passes independently for each of the hotplates.
The Basic settings chapter provides information on
automatically programming the cooking time.
Changing or cancelling the time
Press the 3 symbol several times until the Ú indicator of the
required hotplate lights up. Change the cooking time using
the + or - symbols, or set to ‹‹.
Once the time has elapsed
The hotplate switches off. A beep sounds and in the time
program function display ‹‹ appears for 10 seconds.
The Ú indicator on the hotplate lights up. Pressing the 3
symbol turns off the indicators and stops the beeping.
Notes
■ If a cooking time has been programmed for various zones,
the time program function display always shows the time of
the last hotplate whose power or setting has been adjusted.
■ Cooking times can be programmed for up to 99 minutes.
The timer
The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. This function does not
automatically switch off a hotplate.
How to program
1. The timer can be selected in two different ways:
■ If you have selected the hotplate: press the 3 symbol
twice.
■ If you have not selected the hotplate: press the 3 symbol.
The Ú indicator next to the W symbol lights up. ‹‹ is
displayed on the time program function display.
2. Press the + or - symbol. The basic setting appears.
+ symbol: 10 minutes.
- symbol: 5 minutes.
3. Set the desired time using the + or - symbols.
After a few seconds, the time will start to elapse.
Changing or cancelling the time
Press the 3 symbol various times until the Ú indicator next to
the W symbol lights up. Change the time or set to ‹‹ with
the + or - symbols.
Once the time has elapsed
A warning signal sounds. ‹‹ is displayed on the time program
function display. After 10 seconds the indicators turn off.
Pressing the 3 symbol turns off the indicators and stops the
beeping.
Automatic time limitation
If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. The ”, ‰ symbol and the residual
heat indicator œ/• flash alternately in the display.
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
 
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Constructa CM424252 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Constructa CM424252 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info