714951

Constructa CD75132 Manual

27
Zoom out
Zoom in
Previous page
1/60
Next page
27
General information
Gener al informat i on
Exhaust air mode
: Risk of death!
Risk of poisoning from flue gases that are drawn back in. The
exhaust air must not be conveyed into a functioning smoke or
exhaust gas flue or into a shaft which is used to ventilate
installation rooms that contain heating appliances. If the
exhaust air is to be conveyed into a non-functioning smoke or
exhaust gas flue, you must obtain the consent of the heating
engineer responsible.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
Exhaust duct
Note: The appliance manufacturer does not provide any
warranty for faults attributable to the pipe section.
■ The appliance achieves its optimum performance by means
of a short, straight exhaust air pipe and as large a pipe
diameter as possible.
■ As a result of long, rough exhaust air pipes, many pipe bends
or pipe diameters that are smaller than 150 mm, the optimum
extraction performance is not achieved and fan noise is
increased.
■ The pipes or hoses for laying the exhaust air line must
consist of non-combustible material.
Round pipes
An inner diameter of 150 mm, but at least 120 mm, is
recommended.
Flat ducts
The inner cross-section must correspond to the diameter of the
round pipes.
150 mm diameter, approx. 177 cm
2
120 mm diameter, approx. 113 cm
2
■ Flat ducts should not have any sharp deflections.
■ Use sealing strips for different pipe diameters.
Electrical connection
: Risk of electric shock!
Components inside the appliance may have sharp edges.
These may damage the connecting cable. Do not kink or pinch
the connecting cable during installation.
The required connection data can be found on the rating plate
inside the appliance; to do this, remove the metal mesh grease
filter.
Length of the connecting cable: Approx. 1.20 m
This appliance complies with the EC interference suppression
regulations.
: Risk of electric shock!
It must always be possible to disconnect the appliance from the
electricity supply. The appliance must only be connected to a
protective contact socket that has been correctly installed.
The mains plug of the mains power cable must be easily
accessible after installation of the appliance. If this is not
possible, an all-pole isolating switch must be integrated into the
permanent electrical installation according to the conditions of
overvoltage category III and according to the installation
regulations.
The permanent electrical installation must only be wired by a
professional electrician. We recommend installing a residual-
current circuit breaker (RCCB) in the appliance's power supply
circuit.
Preparing the housing
■ The extractor hood must be installed on the lower edge so
that it is flush with the housing.
■ The housing must cover the entire cooking area.
■ The max. weight of the extractor hood is 15 kg.
Appliance dimensions and safety clearances
■ Take the appliance's dimensions into account.
■ Comply with the safety clearances.
If the installation instructions for the gas cooking appliances
specify a different distance, the largest distance must always be
provided for.
The surround must still be sturdy after the cut-outs have been
made.
To install the extractor hood in a surround, the extractor hood
must be provided with the following dimensions:
Note: All walls of the surround must be at least 15 mm thick.




Width 500-3 mm (appliance width of 53 cm)
Width 700-3 mm (appliance width of 73 cm)
Depth 352-3 mm
Height min. 160 mm (appliance with two
motors)
Wall thickness 16 mm
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Constructa CD75132 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Constructa CD75132 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info