Manual Constructa CD689860 (page 29 of 60) (English, German, Dutch, French)

715171

Zoom out

Zoom in

1/60

Wall-mounting the appliance and levelling it

1. First remove the protective film from the back of the

appliance and, following installation, remove the rest of the

film.

2. When mounting the appliance, ensure that it engages

properly with the mounting supports.

3. If required, the appliance can be moved to the right or to the

left.

4. Firmly tighten the screws for the mounting supports. Hold the

bracket firmly when doing so. ¨

5. If no duct is to be fitted, screw in the two locking screws

without the bracket. ©

Connecting the pipes

If the extractor hood is to be operated in exhaust-air mode, the

pipes must be connected. If the extractor hood is to be

operated in air-recirculation mode, an optional accessory must

be fitted. To do this, refer to the installation instructions

provided.

Note: If an aluminium pipe is being used, smooth the

connection area beforehand.

Exhaust air pipe, dia. 150 mm (recommended size)

Fit the exhaust air pipe directly to the air-pipe connector and

seal the joint.

Exhaust air pipe, dia. 120 mm

1. Fit the reducing connector directly to the air-pipe connector.

2. Attach the exhaust air pipe to the reducing connector.

3. Use suitable means to seal both joints.

Attaching the flue duct

If the extractor hood is to be operated in exhaust-air mode, a

flue duct must be fitted.

The flue duct does not need to be fitted for air-recirculation

mode.

: Risk of injury!

From sharp edges during installation. Always wear protective

gloves while installing the appliance.

: Risk of electric shock!

Components inside the appliance may have sharp edges.

These may damage the connecting cable. Do not kink or pinch

the connecting cable during installation.

1. Separate the flue duct sections by removing the adhesive

tape.

2. Remove the pieces of protective film from both flue duct

sections.

3. Push one flue duct section into the other.

Notes

■ To prevent scratches, lay paper over the edges of the outer

flue duct section to protect the surface.

■ The slots of the inner flue duct section point downwards.

4. Place flue ducts sections on the appliance.

5. Slide the inner flue duct section upwards, attach it to the left

and right sides of the retaining bracket, and then slide it

down to engage it. ¨

6. Screw the flue duct section to the sides of the retaining

7. Clip the lower flue duct section in at the retaining bracket.

The connection cable must not be damaged. ª

Note: If an air-recirculation optional accessory has been fitted

and the extractor hood is to be operated without a flue duct, the

cable must be wound onto the connector.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Constructa CD689860 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Constructa CD689860 Manual

Product: